Question about One For All URC4220 Remote Control

1 Answer


Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 689 Answers

Probably it lost the programmed code. But do not worry, setting the code is really easy. Here is the link for codes

And The link for the instructions

Good Luck

Posted on Jan 11, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Functions on Sharper Image remote control won't work

Try it with an other code to your device.

Feb 17, 2013 | Remote Controls

1 Answer

What is the function of the battery, is it just backup for loss of power?

The battery in the remote control is the power source. The remote control is essentially an LED flashlight that turns on and off very rapidly to send coded signals to the controlled device. The light is infrared "colored", which is not visible to humans.

Like any flashlight, it fades out when the battery gets weak. Also, at some point the encoder chip quits working because there is not enough voltage for the transistors inside it to operate correctly.

Some remote controls (programmable models) store setup information in memory. These either use an internal rechargeable battery or capacitor to retain the data for a short time while the battery is changed, or they use an EEPROM for more permanent storage. The EEPROM models would be more expensive, but they won't lose their programming data if the battery is run down too far.

Apr 29, 2011 | Remote Controls

1 Answer

Why wont my Dish network remote change the channels. Ive already put new batteries in it


When you replaced the batteries in the remote, does any light on the top of the remote light up when you press the select button? If any light other than the SAT button lights up, press and release the SAT button to put the remote back into satellite mode, then try the remote to see if it functions correctly. If none of the buttons light up, make sure all batteries are lined up with the + (positive) facing down. If they are, you may need to readdress the remote to the receiver. I hope this helps.

I have provided a link with instructions on how to readdress the remote to the receiver. Step 4 is for address the remote to the receiver. If you have any problems, please let me know.

Readdress remote to receiver, step 4:

Ray Calo
DISH Network

Feb 19, 2011 | DISH Network IR Remote Control

1 Answer

Remote control doesn't work. Small red light stays lit.

First check the remote control with a similar TV.

By keeping a MW radio receiver you can check the functioning of the remote by pressing the keys. Radio will give garble sound!

If remote is OK , TV has to be checked.

Apr 05, 2010 | Casablanca Fan Versa Touch2 W-72 Remote...

1 Answer

My remote control stopped working

try with simple test. with any camera (mobile) check for any light (infrared light is not visible, only cameras see the infrared light) in front remote control, while press a key, if a flashing light deteted the remote control is ok, and the problem maybe on remote function is selected, normaly using tv and select VCR or AUX, may occur this problem. or a defective receiver sensor.

Jan 02, 2010 | Remote Controls

1 Answer

Remote wont operate sound dock.

hi , To check wether the remote is outputting a infra red signal when a button is pressed try viewing the little LED at the top of the remote through your mobile phones camera , these little cameras pick up a fuller spectrum of light and you should see if flickering. IF you dont then check the batterys/. then the connectors for acid errosion from previous leaking batterys./pull the remote apart and with a pencil rubber clean the contacts on the surface of the circuit board/.The rubber membrain that has the buttons on wash it with warm soapy water , dry thouroughly.last test --go to mapplins and buy a replacement infra red led and change that? , see haow you go whith these tips and report back

Mar 20, 2009 | Bose RC-18S Remote Control

1 Answer

Code for tv

Sanyo is 0154

If this doesn't work with your new remote there is always the way that I have done it in the past and that is to use the find the code function on your new remote. It is a pain but can be done and is quite effective. Each remote is slightly different, but for the most part you would hit the set up botton and hold it in until it starts flashing then hit the T.V. Button and then hit the first code it tells you to hit and then hit the power switch if it doesn't turn off your T.V. then you hit the increment button up, (this is different for each remote so it is important to follow the instruction manual on this part) You bassically keep hitting the incriment button until your code comes up and then it will turn off your t.v.! Then your done. Note: It may take up to 400 pushes of the increment button, but it will work.

Dec 13, 2008 | GE JASRM24912 Remote Control

1 Answer

Universal remote


Aug 24, 2008 | One For All URC4220 Remote Control

Not finding what you are looking for?
One For All URC4220 Remote Control Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top One For All Remote Controls Experts

The Knight
The Knight

Level 3 Expert

66352 Answers

Cindy Wells

Level 3 Expert

4718 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you an One For All Remote Control Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides