Question about Coffee Grinders

1 Answer

2001 nissan primera p11 144 dash bulb replacement

Would appreciate some advice on locating screws/clips etc, so that i can get to dash lights on my primera

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 1,665 Answers
Re: 2001 nissan primera p11 144 dash bulb replacement

Hi have a nice day.
Disconnect the battery cable first. Then, remove the trim around the instruments. You will probably need to drop the steering column to get access
good Luck !

Posted on Jan 19, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Can I replace the grinder in my saeco odeo giro?

yes see the next steps. and fix it. God bless you
  1. Unplug the unit from the electrical receptacle.
  2. Remove the pot and basket. Remove or tape closed the water reservoir lid.
  3. Turn the appliance over and remove all screws that secure the case halves. Lift off the case to expose the heating element and controls.
  4. Inspect the control cavity to determine if the solution is simple: disconnected wire, debris, etc. If so, fix, reassemble, and test. Otherwise, continue with the next step.
  5. Use a DVOM to test the HEATING ELEMENTS and the switch, thermostat, and timer .
  6. Replace any defective parts or decide to replace the appliance, as appropriate.
  7. Reassemble the appliance and reinstall the pot and basket.
  8. Fill the water reservoir approximately half full, then plug in and turn on the coffee maker to test its operation.


Oct 15, 2012 | Saeco Odeo Giro Automatic Espresso...

1 Answer

The retractable cord is stuck so I can't get it out to use it.

(I had the same problem) If you have the model I have, take a small screwdriver and remove screw located in center of bottom plate....remove plate and unwrap cord...reattach bottom and replace screw. I just leave the cord fully extended.

Sep 23, 2011 | Hamilton Beach 80333 Grinder

1 Answer

I cannot move the screw to change the grind. How do I do this on a G9.

It should be easily move.I don't know how its stuck.
BUT a Good advice.If you in future disassemble the grinder.Then,make sure you either count the screw rotation of unscrewing or just put paint mark on screw where it was previous fixed.
Once you open grinder its very hard to put it back to work grinder like before.
Please rate my work

Sep 19, 2011 | Bunn G9 HD Electric Burr Grinder

1 Answer

Mr coffee IDS55-4 suddenly stopped working. The blade is intact. What could br the problem and what can I do?

Circuit protection in this grinder is done with a resettable fuse. Mine failed the first time I used it. Fortunately, it's relatively easy to replace.

  1. Remove the plastic plate covering the bottom of the grinder. It is held in place by three screws.
  2. Remove the power cord strain relief inside the grinder. It is held in place with two screws.
  3. Remove the motor. It will only come about half way out of the enclosure.
  4. My fuse was fastened to the motor with a copper tie, which needed to be loosened to access the fuse.
  5. Remove the fuse by un-soldering one end from the motor and clipping the wire that it is crimped to on the other side. See attached photo of the fuse after it was removed.
  6. Replace with a 15A fuse or just solder the end of the black wire directly on to the motor. If you don't replace the fuse, you should be careful not to run the grinder for prolonged periods of time because your may destroy the motor.

Oct 06, 2010 | Mr. Coffee IDS55 Electric Blades Grinder

1 Answer

Just bought a used one, seems like the espresso grind is pretty course, is there an adjustment I can make?

To adjust this grinder turn the adjustment nob to the finest setting (ESPRESSO or TURKISH) Locate 2 small set screws on the adjusting nob. Loosen these screws (do not remove them) about one full turn. Start the grinder and, with it running, VERY SLOWLY and GRADUALLY, turn the CENTER adjustment screw clockwise until you begin to hear the burrs begin to touch (whirring sound). Back off the center screw about 1/16 of a turn, shut of grinder and re-tighten the set screws. Then try the grind on DRIP or there about for brewed coffee.

May 21, 2010 | Grindmaster 495 Electric Grinder

1 Answer

A-9 coffee grinder very weak

The last time I had to do this I went to a 'mom & pop' hardware store with the old brushes and looked thru the bins until I found a match. Seems like it was pretty straitforward to replace them, just a few screws and clips. While you have it open, gently clean out the grooves on the rotor with a dental pick or toothpick (that's the dust from your worn out brushes). That will help it run longer and stronger.

Nov 01, 2008 | Coffee Grinders

2 Answers

Krups coffee mill

There are four slots in the bottom through which you can see the attachment clips. These clips are not mounted on the base but clip into the base. There is a special 4 prong tool that is used to depress these but if you don't have one, which you most certainly will not have, you need to use four small nails to open it up. Looking at them from the bottom, the clips look like a capital E with an extra horizontal leg. try to drive your nails in to the middle of the back of the E, that is on the flat side. After you have done this use a claw hammer to pry the bottom off by inserting the claws into the seam between the bottom and the top and twisting until something gives. You will probably get the bottom off without destroying more than one of the clips. No matter, you can tape or glue the ****** back together.

If power lose was your problem, remove the switch from its clip then test it to see if depressing the button causes the contact rod to touch both of the copper plates which are mounted on opposite sides of the switch, be careful while making this test - you have to have the grinder plugged in and you do not want to be touching any electrical contacts, the blade or the motor. Also beware of the torque from the motor causing you to drop the grinder. Also, beware of the torque from the motor causing you to drop the grinder in the unlikely event that it is working.

If depressing the switch doesn't cause the switch shaft to come in contact with both plates then get a pair of plyers and bend the copper plates down so that contact can be readily be made.

Retest to confirm the fix works then reassemble, using tape, glue or whatever and then -- it's coffee time!!

Jul 23, 2008 | Krups 203 Grinder

1 Answer

04 nissan primera 1.8 radio

you have a nats system fault re-code keys or disconnect battery for 24 hrs

Jan 07, 2008 | Coffee Grinders

1 Answer


There is a fuse under the drivers side dash and just to the left of the stearing colum, it's about an inch square and brown. I know because mine was clicking and I had to replace it... good luck.. ;-)

Jan 05, 2008 | Coffee Grinders

4 Answers

Krups GVX2-12 Electric Burr - Thermal Fuse

Open the grinder by removing both knobs.
The front knob is held in place by friction. Use two flat head screwdrivers to pry it off.
The side knob is held in by tabs you have to push. Pry forward to expose the tab, and use another screwdriver to press the tab, and use the other screwdriver to press the tab on the other side.
Now look at the bottom of the grinder. There are four tabs on the outer shell, use screwdriver s to pry the tabs to separate the bottom of the grinder from the shell, and pull off the shell. Your fuse should be attached to the motor wiring coil.

Jan 01, 2008 | Krups GVX2-12 Electric Burr Grinder

Not finding what you are looking for?
Coffee Grinders Logo

Related Topics:

1,578 people viewed this question

Ask a Question

Usually answered in minutes!

Top Coffee Grinders Experts

Ernest R
Ernest R

Level 3 Expert

1618 Answers


Level 3 Expert

345 Answers

Tony R.
Tony R.

Level 2 Expert

24 Answers

Are you a Coffee Grinder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides