Question about Toshiba 55H70 55" Rear Projection Television

2 Answers

Hitachi MD# 53uwx10ba Blue canono leak

Blue color cannon is leaking after i meddled with it i was trying to see if i could remove to specs from inside the cannon that were appearing on the screen. the picture a little obscure as i took the cannon apart" i would like to know what is my fix if any or where to purchase the blue color canon at a good price

Posted by on

  • 1 more comment 
  • marcelking Jan 12, 2008

    Hitachi model 53uwx10ba
    What is the oil used inside the blue color gun are there any web sites where the bulb itself can be purchased along with the oil necessary to refill the lost oil..thank you in advance for any information.
    marcelking

  • marcelking Jan 15, 2008

    Im trying to avoid calling a tech for the simple reason of cost.the magic $400 or 500 comes to mind for about $800 more i can get a nice lcd but would rather know my cost up front for such a problem as i have already removed all the oil off the board and sprayed it clean with electrical cleaner of course now i have no power to the color bulbs but interment power to the board...I just dont know what to do at this time..Ps i emptied the canister of all its oil dry and replaced it with mineral oil you guys will brobaly be getting a kick out that one but it made oall the sense in the world to me at the time..thank you BMW Rider..
    marcelking

  • marcelking Jan 15, 2008

    Well gentleman im puling the sheet over this one as my my desire supersedes my knowledge of what you pros already know,its a sad thing because i know anything can be fixed and perhaps late at night i will take this unit apart to furhter study what it is that, has given pretty good service since 2002 its to bad its not a GM.
    Thank you everybody for your assistance willing to help an unknown person..So lets hear it for humanity,thanks everybody.
    marcelking

×

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 232 Answers

Hi, you need to call a tech now, the fluid is very caustic to your board and needs to be cleaned asap, the blue tube does not have to be replaced (good thing as it`s veeery expensive), Call atech right away and he`ll be able to stop the tube from leaking, good luck, BMW Rider

Posted on Jan 14, 2008

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toshiba Master
  • 8,617 Answers

You dont need another Blue gun. We can show you how to repair your seal and where to get the parts. You will need the service manual. you can get it at the following link. Click on toshiba and you'll see your model it cost 10.99 and we provide unlimited chat support to help you repair your set. Then if you click on the contact us link and provide your email address we will email your manual along with instructions on how to enter the chat sessions. I am one of their techs. Hope this helps.
http://servicemanuals.vstore.ca/

Posted on Jan 13, 2008

  • Sonny Berry
    Sonny Berry Jan 15, 2008

    Check the capacitors in the area where the coolant leaked also the Diode and resisitors. Coolant has a way of destroying the solder connection. remove the solder on those components and resolder. Mineral oil will destroy your CRTs if you power it up. Those tubes get hot you need the proper coolant you can get it at Matelectronics.com

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hitachi 53uwx10ba service mode


are you using an HDMI cable? is it a cheap thin cable or heavy duty?
HDMI cables carry sound but it's possible you don't have it seated completely or it's a cheap cable. or your audio settings on your TV are not set to HDMI if that's the cable you're using. try running your audio setup on the TV Menu.

Dec 03, 2013 | Televison & Video

1 Answer

Hitachi 53UWX10BA dynamic convergence works but blue is blurry


I know this set very well---you are saying convergence adjusts ok everywhere? If you understand that the blue is usually de-focused a little----there are only two ways to adjust the focus of each tube-----

1.) Behind the front speaker grill there is an inspection plate---with it removed you will see a small black plastic block with 6 controls on it; it is the MASTER SCREEN/ FOCUS BLOCK

2.) THREE of the controls left to right are Screen controls(red, green and blue) and the other 3 are FOCUS--IT IS ALL black and you need to look close to identify which is focus and which is screen---you are looking for the BLUE focus control(one of the 6)

3.) With the convergence grid on screen cover the RED and GREEN lens in the set and try to adjust the focus of the blue(I presume you know how to put the set into the Convergence mode?

4.) The only other way to adjust the Blue focus is from the back of the set---with the Red and Green lens covered up place a blanket over the top of the set that covers the whole screen--from the back of the set you will note that all three of the black focal lens have a wing nut---with the convergence grid up and only blue lines present(Green and Red lens covered with a cloth) look from behind the set at the grid---loosen the wing nut on the blue lens and slowly slide the lens left or right until the blue has the best focus possible----if it will not adjust with the focal lens or the front focus control you have a circuit problem.

I do this here for free and if this information helps you take a minute and give me a vote here. If you have any questions or need advice reply to this posting here and I will assist you.

SD TECH

Sep 14, 2009 | Hitachi 53UWX10B 53" Rear Projection...

1 Answer

Hitachi 53UWX10BA HDTV adjusting color


Hi, Your tv model has a small light blue color button inside for manual adjustmnet mode. You will have to remove the front covering below the screen. its just attached with velcrow. Then there will be a centre wooden pannel with the the switching box screwed to tv front with around six screws.Open this panel and look to the left corner of the chasis boards in front of a small metallic box. Thats the switch you have to press to get into manual adjustment mode. use remote to adjust the colors. once done press it again to exist. Visit www.fixurtvs.com to find out more about tv FAQs. Thanks if you found it helpful.

Apr 29, 2009 | Televison & Video

1 Answer

Hitachi 53UWX10BA HDTV with convergence problem for blue


No there are no quick fix options for this fault. The convergence amplifiers operate similar to a high power audio amplifier, so if there is an impairment anywhere in the system, it will result in distorted audio, or in the case of television convergence amplifiers, a color won't align. The convergence power pacs need to be replaced and the out of tolerance precision resistors located near the power pacs need to be carefully checked and replaced as necessary.

It is also possible that there are root faults that cause the amplifiers to go bad which include bad connections or a bad digital control module. This repair is possible for anyone having basic electronics knowledge and soldering skills.

Apr 28, 2009 | Hitachi 53UDX10B 53" Rear Projection...

1 Answer

Blue color doesnt muve up


hi there. sounds like a bad convergence IC. possibly a broken connection(s), parts are located on a large heatsink near the center of the main chassis, part number is STK391-110 for standard definition and STK391-570 for high definition, the location and part numbers can vary from model to model and year to year. hope this helps.good luck and be safe.

May 26, 2008 | Hitachi 53UWX10B 53" Rear Projection...

1 Answer

Problem continued


Good Day;

When you activate the Mj focus the TV is restoring the data from the TV's digital circuits. So, you have the ability to change the IC's you can do this.

You need to go into the con service mode. Take off the front grill, remove panel, 6 - 8 screws. From the front there is a switch on the left hand side, it is small, white button with TV on. now you are in the service mode, using TV's remote adjust. Make sure you save dat. Go hit on line site get more info.

Goo0d Luck!

May 25, 2008 | Hitachi 53UWX10B 53" Rear Projection...

1 Answer

PROJECTION TV HITACHI ULTRAVISION COLOR CONVERGENCE PROBLEM


it sounds like your blue convergence ic is getting weak you need to replace the ic's STK392-110 and you should replace both because when 1 is bad the other will go real soon. They are inexspensive at the sight I posted and you will also get free tech online support if you purchase them there.
http://servicemanuals.vstore.ca/

Apr 12, 2008 | Hitachi 53UDX10B 53" Rear Projection...

1 Answer

Red color on screen is warped on my LCD projector TV.


Normally the oily fluid coming from a picture tube, is the coolant from the tube. It's very combustible and have been known to start a fire. You have two problems in this set. A leaking blue picture tube. A convergence circuit that needs repaired. Call a local servicer and see if they will give you an estimate over the phone. It's time to start looking for a new digital set. Good Luck.

Jun 23, 2007 | Hitachi 50UX58B 50" Rear Projection...

1 Answer

Picture Problems with Hitachi 53" Projection TV


most tv shop's will replace convergence ic's,which your tv needs.Thepart number is stk392-180 very common You need 2 plus poss resistors,3 bucks apiece

Mar 20, 2007 | Hitachi 53UDX10B 53" Rear Projection...

Not finding what you are looking for?
Toshiba 55H70 55" Rear Projection Television Logo

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toshiba Televison & Video Experts

The Knight
The Knight

Level 3 Expert

75846 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Jaime Hernandez

Level 3 Expert

2336 Answers

Are you a Toshiba Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...