Question about Samsung CLP 300 Laser Printer

1 Answer

The back and rear panel is quite hot and the ubit will not print

The back and rear panel is quite hot and the status light turns red after a short period and the unit will not print

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Samsung Expert
  • 406 Answers

Install a smart panel software from samsung. you will get exact error.

Posted on Nov 22, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is red light on samsung clp- 315 and it is not printing


Does one of these situations apply to you?

The Status LED light is Red and the Toner lights are OFF (Check Smart Panel for message)

  • A Paper Jam has occurred.
  • The Front, Top, or Back Cover is open.
  • There is no paper in the Paper Tray.
  • There is a problem with the Waste Toner container.
  • A major error has occured.

The Status LED light is Blinking/Flashing Red and the Toner light(s) are Red

  • The Toner cartridge(s) that are Red need to be replaced. (Can still be used to print, but quality is unreliable)

The Status LED light is Red and the Toner light(s) are Red

  • The Toner cartridge(s) that are Red need to be replaced. (Printing is not available)
  • The Toner cartridge(s) are not installed properly.
Source: samsung troubleshooting guide for CLP-315

Sep 25, 2010 | Samsung CLP 315 Laser Printer

1 Answer

Printer stops when printing should begin with red light in status


There is a few reasons that cause the status light to turn red, paper jam, paper empty, toner cartridge empty, cover open and waste toner cartridge full. The PC Smart panel utility should give you an exact fault condition. Hope this helps.

Jul 08, 2010 | Samsung CLP 300 Laser Printer

1 Answer

Status indicator flashes 3 short times, then one long red flash


Once the status light blinks 3 times, this is an indication that there's a problem with the lamp. The lamp may need a replacement.

If you replace the lamp, but get the same problem, check the inverter board.

If you're not sure where the inverter board is, then you may need to contact a pro for your safety.

Good luck and have a good evening!

Feb 14, 2010 | Mitsubishi WD-52327 52" Rear Projection...

1 Answer

Red lights flashing. I dont think the ink is out and i did try taking them out following the instructions and put the same ones back in but it still won't print and the light is still flashing, will it...


Printer wouldn't print if red light flashing. Check status monitor for detail? Are some ink not recognized? Do replacement procedure from status monitor on "How to...". Unplug all ink tank. Plug only one ink tank . See status monitor. Is ink tank recognized. repeat procedure, and add ink tank 1 by 1. How about status monitor then?

Jul 09, 2009 | Epson Stylus CX5000 InkJet Photo Printer

1 Answer

Status light remains red


download smarrt panel from samsung website,install on pc and run.have printer connected.will resolve issue.

Jul 06, 2009 | Samsung CLP 300 Laser Printer

2 Answers

Mitsubishi WD-62525 Red Status Light After Cap Replacement


A steady red light: there is a short on the DVI cable from FMT to DMD disconnected

Sep 09, 2008 | Mitsubishi WD-62525 62" Rear Projection...

Not finding what you are looking for?
Samsung CLP 300 Laser Printer Logo

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Office Equipment & Supplies Experts

mukhtar21 shaikh
mukhtar21 shaikh

Level 3 Expert

2017 Answers

HEMANT GROVER

Level 2 Expert

167 Answers

CheckitRight
CheckitRight

Level 3 Expert

1362 Answers

Are you a Samsung Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...