Question about Akai PT5250A Television

1 Answer

IT DOES NOT TURN ON, NOT EVEN THE RED LED LIGHT

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Akai Master
  • 5,138 Answers

On the power supply board is a thyresistor will be up on front of board resolder this should fix problem. Ive fix alot of them that have same problem Part acts as a heat conductor switch they were not solder in Good so after awhile solder is bad.

Posted on Nov 19, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hard drive led light stays on after i turn off computer


have a look at p28 of the set up guide
http://downloads.dell.com/Manuals/Common/inspiron-560_setup%20guide_en-us.pdf
and read this for an idea also
Power LED stays on when computer shuts down
(I searched the internet on "Red led light in front of computer stays on after i turn off computer " to obtain many results, this is just one)
23.February.2015

Apr 29, 2014 | Dell Inspiron 560 PC Desktop

1 Answer

Red LED will not go off


You have unheard messages on the voicemail system provided by your telephone company. This system takes messages when someone calls while you're already on the phone. Please contact your telephone company for instructions on accessing their voicemail system.

May 06, 2013 | Uniden 5.8GHz Expandable Cordless Phone...

2 Answers

I am trying to charge my phone right now but it is just a constant red light where it would usually be orange and it is saying 0% charged


did you run the battery completely flat?

my phone if it has gone dead, when plugged in to charge, has a red LED for about 5 minutes where you cannot even turn it on it is that dead. after those minutes pass the phone can then be turned on, and the LED changes color to orange to indicate it is charging and is also powered on.

Jul 12, 2010 | HTC G1

1 Answer

Power light on& status light on


The power red led indicates that your device is "power on" , but the status led still red and turn to green if the device ( video input )received video signal ( from DVD player, Laptop etc. ) .

Apr 29, 2009 | Computers & Internet

1 Answer

Red led light on constantly


electronic circuit needs replacement

Feb 01, 2009 | PUR (FM-9500) Air Purifier

1 Answer

Blinking red light for "new message" will not turn off (model DECT2085)


Try pressing and holding the "find handset" or "page" button on the basestation until the phone stops beeping. This should clear the new message LED indicator.

Nov 07, 2008 | Uniden 5.8GHz Expandable Cordless Phone...

1 Answer

Free Pulse


The following procedure will re-establish the communication link between the Headphones and the Wireless adapter, this is called "pairing". Before you start please make sure both the headphones and the wireless adapter are fully charged and turned off.
Note: The headphones and the wireless adapter come pre-paired from the factory.
1. Press and hold the power button on the headphones. See Figure 1.
headphone.jpg
Figure 1

2. Continue to hold the button down until the LED starts flashing red/blue in an alternating pattern. Release the button when the LED starts flashing red/blue. See Figure 2.
headphone-flash.gif
Figure 2
3. Once the headphones LED is flashing red/blue, press and hold the power button on the wireless adapter. See Figure 3.
receiver.jpg
Figure 3
4. Hold down the button until the LED starts flashing red/blue in an alternating patter. The LED will blink blue, then turn off for a few seconds then blink red/blue. Release the button when the LED starts flashing red/blue. See Figure 4.
receiver-flash.gif
Figure 4
5. Once both the headphones LED and the adapter LED is blinking red/blue, press the volume up button once on the headphones. See Figure 5.
headphone-volumeup.jpg
Figure 5
Once the headphones is paired with the adapter, the LED on the headphones will blink blue once every two seconds. See Figure 6.
headphone-flash2.gif
Figure 6
When the adapter is paired the LED will be solid blue. See Figure 7.
receiversolid.jpg
Figure 7
The adapter may continue to blink red/blue for a few seconds even after the headphones LED starting blinking blue. This is normal; the adapter may take a few additional seconds before the LED turn solid blue.
Once the headphones and the adapter are paired, it is not necessary to pair them again even if the batteries on both units are completely drained.
Additional Note: Repeated pairing will not improve the sound quality or give the headphones and the adapter a cleaner connection.

Mar 11, 2008 | Logitech FreePulse Wireless Consumer...

Not finding what you are looking for?
Akai PT5250A Television Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Akai Televison & Video Experts

Jaime Hernandez

Level 3 Expert

2318 Answers

The Knight
The Knight

Level 3 Expert

74383 Answers

Radames Pagan
Radames Pagan

Level 3 Expert

196 Answers

Are you an Akai Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...