Question about Radio Shack Radio Communications

1 Answer

I have a Pro60 that wont recieve a signal, volume works, scan works, no signal at all

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,761 Answers

Does adjusting the squelch make the scanner stop? If so, you likely just don't have the active frequencies for your area programmed into the scanner. For a comprehensive list of your area's active freqs check with databases such as RadioReference.com and CityFreq.com

Posted on Nov 21, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My pa system recieves signal but wont send any sound out


Check cables to speakers from amp if any. Possible crossover or channel failure.

Apr 08, 2014 | Audio Players & Recorders

1 Answer

No volume flow


retight the spring contacts batteries for better contact, the r.control emit infrared signal to the reciever.
2= open the r. control for clean the keypad switch for dirty, oxide, etc, bad contact or open switch
3= test again, if doesnot work, go to the repair shop tv for fix it.
God bless you
7_20_2012_9_35_25_am.gif

Jul 19, 2012 | Televison & Video

1 Answer

Wont recieve signals


You more than likely got water on the circuit board. Try drying off the circuit board or get a new one

Jun 27, 2010 | Exceed-RC 1:16 Nitro powered truck,W/SH...

1 Answer

We have to hold the remote control button hard and straight at the reciever for ti to work


The volume keys should be working by default, but you may have volume punch through turned on (meaning the remote is sending signals for TV or CABLE volume function no matter what mode you are actually on). To unlock volume control for AUX mode, do the following:
1. Press and release AUX
2. Press and hold SETUP until the remote blinks twice
3. Type 993
4. Press and release VOL-
The remote should blink four times to confirm unlock.

May 20, 2010 | Yamaha HTR-5860 Receiver

1 Answer

Not scannig right wont receive any signals radio shack pro-89


Turn scanner on, half volume,turn squelch untill silent,then push scan........hope this works for you.....

Mar 01, 2010 | Uniden BC60XLT-1 Handheld Scanner

1 Answer

The reciever volume will not ajust .. It is fixed at one set volume


Volume controls today are not potentiometers anymore. Manufactures use devices called encoders. When you spin the encoder it sends a binary signal to a decoder chip that will in turn increment or decrement the volume. Either your decoder chip is bad or the encoder itself needs replaced.

Feb 10, 2010 | KLH R3100 Receiver

2 Answers

New tv. won't work


Press the input button and select where you have the satellite plugged in.

Aug 12, 2009 | Dynex DX-LCD19-09 19 in. LCD TV

1 Answer

Protect displaying


Protect on any reciever usually means that it has reached its maximum capacity of volume (known as clipping) and at the reciever is now automatically reducing the volume to avoid damage. This some times is triggered if the reciever was used hard and is now damaged so you would need to bring it to a repair shop. Sometimes its caused by a bad wire to the speakers, a short to say. Check all your wiring, make sure its not overheating and getting plenty of air. Some where its recieving a signal telling it to go into protect mode.

Joe

May 28, 2009 | Audio Players & Recorders

1 Answer

Have no volume on only one channel on Panasonic TH-42PX60U


Try the SAP - same thing happened to me and had to cycle through the audio tracks to get audio back on for that one channel. Good Luck!!!

May 12, 2009 | Panasonic TH-42PX60U Television

1 Answer

My xbox 360 wont recieve a signal from my computer.


if your laptop get a signal than buy a eithernet cable and coonect your xbox 2 the laptop and go 2 your network settings and check the box that say share connection than wait a few mins. and try to connect to xboxlive this should work because thats how i get on xboxlive at my house.

dalvon78@yahoo.com

Jan 05, 2009 | Microsoft Xbox 360 Console

Not finding what you are looking for?
Radio Communications Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Radio Shack Radio Communications Experts

John
John

Level 2 Expert

509 Answers

Greg Cann
Greg Cann

Level 3 Expert

1114 Answers

Jason

Level 2 Expert

211 Answers

Are you a Radio Shack Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...