Question about Cameras

Open Question

Problem with tasco trail sentry

I have the cheaper tasco trail sentry that looks the same, and when i turn the camera on it mite stay on for few minutes but will not take picure and turns its self off, then i have to pull a battery out and put back in to get it to come n again only to do the same thing over

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1894 Answers

SOURCE: Bushnell 3.2 trail sentry

its asking for the master password

Posted on Mar 16, 2008

Ad
leepania
  • 1099 Answers

SOURCE: When I turn my camera on it stays on for a few

1. Make sure you will install a new or fully charged battery/batteries into your camera. Please use lithium batteries Ni-Mh or rechargeable Batteries (2000 M.Amp or higher). 2. Clean the battery contacts. a. Remove the battery/batteries and the memory card from your camera, then wipe the battery contacts with a soft, clean cloth. b. Reinstall the battery/batteries into your camera 3. Turn on your camera without the memory card. (If it works then it?s your memory card that is faulty)

Posted on Jan 14, 2010

chelseawells
  • 11 Answers

SOURCE: will not turn on

This is likely the cause of an internal screw that has come loose, it's very common on the G9. A great place to get help with this G9 problem is: camerasandparts.com since they just specialize in these powershots. They not only have the fix available but they have the correction so this never comes back, that comes with their no power service for the G9's automatically. I hope that helps, that's the place if you need help with a powershot, best of luck

Posted on Jun 24, 2010

monteagle
  • 38 Answers

SOURCE: I got my Bushnell Trail Sentry Digital Trail

the first time the camera is used the code should be 0000 unless previously changed,try removing and reinstalling the batteries,this hould start your set up again.
press and release the power button and wait for 4 H's,"HHHH" to appear,this may give you another chance to use 0000 or whatever you chose as your password.press enter after each digit,then press enter again.the indicator should display PASS.if it displays ERRO then it is the wrong password.there is a password recovery service provided by Bushnell at 1-800-423-3537 and press option 2,you will need to provide your serial number to the representative.

hope this helps.

Posted on Jan 09, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My tasco trail cam boots up with 4 dashes on display. Nothing else.


When you hit enter does it change the dashes to zeros? Default code is 0000

Apr 27, 2014 | Bushnell Trail Sentry 11-9200 Digital...

1 Answer

I have a tasco 3mp trailcam that i have not used in atleast 2 years can not remember the password please help


To reset the password:

Turn unit on and wait for password prompt
Depress the and hold the enter button until camera switches into 5-digit password mode _ _ _ _ _.

Trail sentry systems will not indicate 5-digit mode on the screen, but will indicate _ _ _ _ instead of HHHH .

Press enter to confirm 5 digit mode

Enter 5-digit code 66214 and press enter button( trail sentry cameras will accept a 5th Digit after the 4th digit is entered in the _ _ _ _ screen.

Camera will now go into operating mode, and user can now program a new password from the setup mode.

Follow this link to see the user manual PDF:

http://www.bushnell.com/manuals/trail-scout/119000TrailSentry_manual.pdf

Aug 23, 2011 | Tasco 3mp Trail Cam Black-cameras

1 Answer

I just bought a Tasco Digital Trail Camera - 119223C . During the setup my camera display also shows Loc and the SD Card flashes. The instruction manual does not reference this setup code. Does...


I just bought,last August, a Tasco Digital Trail Camera - 119223C . Took pictures until Jaunary 2011, my camera display shows Loc and the SD Card flashes. The instruction manual does not reference this setup code. Does anyone know what 'Loc' means? I tried to reformat card, I also so not get a Y/N option for formatting. I bought a new card and changed batteries. no change!

Nov 14, 2010 | Bushnell Trail Sentry 11-9200 Digital...

2 Answers

I have a tasco digitail trail camera. i inadvertantly changed passwordf i guess. it keeps giving me error. i cannot do anything to it on now. is there anything i can do


To reset the password:

Turn unit on and wait for password prompt
Depress the and hold the enter button until camera switches into 5-digit password mode _ _ _ _ _.

Trail sentry systems will not indicate 5-digit mode on the screen, but will indicate _ _ _ _ instead of HHHH .

Press enter to confirm 5 digit mode

Enter 5-digit code 66214 and press enter button( trail sentry cameras will accept a 5th Digit after the 4th digit is entered in the _ _ _ _ screen.

Camera will now go into operating mode, and user can now program a new password from the setup mode.

Follow this link to see the user manual PDF:

http://www.bushnell.com/manuals/trail-scout/119000TrailSentry_manual.pdf

Aug 01, 2010 | Cameras

2 Answers

I cannot reset the password on my tasco trail camera


To reset the password:

Turn unit on and wait for password prompt
Depress the and hold the enter button until camera switches into 5-digit password mode _ _ _ _ _.

Trail sentry systems will not indicate 5-digit mode on the screen, but will indicate _ _ _ _ instead of HHHH .

Press enter to confirm 5 digit mode

Enter 5-digit code 66214 and press enter button( trail sentry cameras will accept a 5th Digit after the 4th digit is entered in the _ _ _ _ screen.

Camera will now go into operating mode, and user can now program a new password from the setup mode.

Follow this link to see the user manual PDF:

http://www.bushnell.com/manuals/trail-scout/119000TrailSentry_manual.pdf

Nov 06, 2009 | Bushnell 11-9000 Digital Camera

1 Answer

Bought yesterday. Following instructions,0000 is not the default code on this unit!!


Try this:
Trail Scout and Trail Sentry camera re-programming procedure.
1) Turn unit on and wait for screen to prompt password
2) Press the enter button and hold until camera switches into 5-digit password mode _ _ _ _ _.
Trail sentry cameras will not indicate 5-digit mode on the screen, but will indicate _ _ _ _ instead of HHHH .
3) Press enter to confirm 5 digit mode (for trail scouts go to next procedure).
4) Enter 5-digit code 66214 and press enter button( trail sentry cameras will accept a 5th Digit after the 4th 0ne is entered in the _ _ _ _ screen.
5) Camera will now go into operating mode, and user can now program a new password from the setup mode

Oct 04, 2009 | Bushnell Trail Sentry 11-9200 Digital...

1 Answer

My trail sentry will not let me reset the code


Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} Trail Scout and Trail Sentry camera re-programming procedure.
1) Turn unit on and wait for screen to prompt password
2) Press the enter button and hold until camera switches into 5-digit password mode _ _ _ _ _.
Trail sentry cameras will not indicate 5-digit mode on the screen, but will indicate _ _ _ _ instead of HHHH .
3) Press enter to confirm 5 digit mode (for trail scouts go to next procedure).
4) Enter 5-digit code 66214 and press enter button( trail sentry cameras will accept a 5th Digit after the 4th 0ne is entered in the _ _ _ _ screen.
5) Camera will now go into operating mode, and user can now program a new password from the setup mode

Oct 04, 2009 | Bushnell Trail Sentry 11-9200 Digital...

3 Answers

Bushnell Trail Sentry Camera- forgot password


Trail Scout and Trail Sentry camera re-programming procedure.
1) Turn unit on and wait for screen to prompt password
2) Press the enter button and hold until camera switches into 5-digit password mode _ _ _ _ _.
Trail sentry cameras will not indicate 5-digit mode on the screen, but will indicate _ _ _ _ instead of HHHH .
3) Press enter to confirm 5 digit mode (for trail scouts go to next procedure).
4) Enter 5-digit code 66214 and press enter button( trail sentry cameras will accept a 5th Digit after the 4th 0ne is entered in the _ _ _ _ screen.
5) Camera will now go into operating mode, and user can now program a new password from the setup mode

Oct 01, 2009 | Bushnell Trail Sentry 11-9200 Digital...

1 Answer

Decode to reprogram new pass word


Try this:
Trail Scout and Trail Sentry camera re-programming procedure.
1) Turn unit on and wait for screen to prompt password
2) Press the enter button and hold until camera switches into 5-digit password mode _ _ _ _ _.
Trail sentry cameras will not indicate 5-digit mode on the screen, but will indicate _ _ _ _ instead of HHHH .
3) Press enter to confirm 5 digit mode (for trail scouts go to next procedure).
4) Enter 5-digit code 66214 and press enter button( trail sentry cameras will accept a 5th Digit after the 4th 0ne is entered in the _ _ _ _ screen.
5) Camera will now go into operating mode, and user can now program a new password from the setup mode

Sep 30, 2009 | Bushnell Trail Sentry 11-9200 Digital...

1 Answer

Forgot password on bushnell trail sentry game camera


If the Bushnell Trail Sentry 11-9200 is turned on without an SD card in place, it may need to be reset. Reset it by pulling one of the batteries out partway, insert a new or empty SD card, and put the battery back in place. Read this Set Up Guide for instruction how to set up your passcode.

If you are looking for a replacement trail camera, or you want to buy another, go to my Hunting Supplies Website and browse through the different name brands offered for sale here. http://hunting-supplies-net.com/

Dec 09, 2008 | Bushnell Trail Sentry 11-9200 Digital...

Not finding what you are looking for?
Cameras Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cameras Experts

kakima

Level 3 Expert

102366 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

Are you a Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...