Question about Dewalt DC925 Cordless Drill

1 Answer

Drill works fine but wont engage hammer. the torque ring goes from 1 to 21 ok but i cant engage the drill or hammer setting

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 197 Answers

On my DW988 the ring would go past 21 a couple of clicks to a symbol that looks like a yellow T and that would be hammer mode when I press down to drill.

Posted on Nov 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When hammer or hammer drill action is selected hammer action is not working


The ring of the impact bolt in front inside the locking sleeve where the chisel is driven on can be blocked (also broken part ) but not to see until you remove the parts .

Jan 11, 2016 | Hammer Drills

2 Answers

Torque limiter quick to engage Why?


Usually it is a worn clutch that will cause this.

May 26, 2014 | Drills

1 Answer

110 v comb drill does not engage to hammer setting


You don't say which model or make. could be just the selector.

Oct 19, 2012 | Drills

1 Answer

Can't engage drill or hammer settings on de walt dc 925 xrp


Try turning the ring to 2 or 3 and run the drill holding the chuck so the clutch slips then try turning it to drill setting. Also try to do it in different speed settings. If not it sounds like a fault in the gear module. It might just be a metal clip just under the clip in side. Undo the 4 screws holding the gearbox onto the housing and carefully remove it, you might see the fault or loads of dirt that needs cleaning. Go to http://www.2helpu.com/world/map.aspx for a drawing.

Jun 01, 2012 | Dewalt 18v Battery Hammer Drill Dcd950...

1 Answer

Type your problem for a solution...


I'm answering without knowing which model you have but, there are some Dewalt drills that will go into hammer and/or drill mode only if the speed selector is in 2nd gear. The torque settings are accessable only in driver mode. Short of that you may have broken parts in the transmission that can only be repaired by replacing the transmission.

Dec 28, 2011 | Dewalt Drills

1 Answer

Hi i cant move my torque setting its just stuck on hammer and drill,speed ie 1 to 3 is okay but i cant get it to move to 1 to 21 is this a common problem thanks


You have an internal issue in the housing. Sometimes they will move while slowly operating the drill. If that does not work, the housing has to come apart, more specifically the head.

Jan 16, 2010 | Dewalt DC920KA Heavy Duty Xrp 18V Cordless...

1 Answer

My chuck would not rotate,(Porter cable 14.4V Hamm drill) but the motor would turn as normal as I pressed the switch. There was a grinding noise as the motor turned which I first heard when I attempted to...


It sounds like you were between gears. When you are in neither low or high, you are sort of in neutral. Normally it isn't a big deal. It happens to me occasionally, and I do what you did. You should be OK.

Jul 18, 2009 | Porter Cable 14.4V Hamm Drill Kit

1 Answer

I have a Ridgid 24V LI Hammer Drill. It was working fine and then suddenly it has lost lost torque. It sounds fin and seems to run fine but anything beyond screwing in a wood screw it just clicks like...


Make sure the speed lever is not in between speeds, if not, time to get a new clutch/tranny or take it back to Home Depot if its new. I think it comes in one piece. Please rate me.

Apr 07, 2009 | Drills

1 Answer

I have an 18v dewalt hammer drill dc925 and cant get it on the hammer setting?


It's one of the settings on the clutch ring. Or do you mean it won't turn there?

Mar 07, 2009 | Dewalt 18 Volt Compact Drill Kit

1 Answer

The motor turns but the clutch will not engage


Take the drill out of the hammer drill setting when in reverse.  Using the drill setting with the speed on 1 will give the power to free the bit.  If the clutch will not engage, GENTLY but firmly switch between forward and reverse.  This should work just fine.   I hope this solution brings you success!  Best Regards,  Michael Mittelsdorf

Dec 26, 2008 | Drills

Not finding what you are looking for?
Dewalt DC925 Cordless Drill Logo

Related Topics:

346 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dewalt Drills Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

yadayada
yadayada

Level 3 Expert

75066 Answers

Jim Thurston

Level 3 Expert

670 Answers

Are you a Dewalt Drill Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...