Question about Zebra Z4Mplus Label Printer

1 Answer

Zebra 4m Our Printer Zebra 4M stops after each lable.We send usualy about 100 lables the same contenst. It takes very long time because instead of contineous flow print it stops after each lable for a 1-2 sec.Can we solve this? Alex

Posted by on

1 Answer

Re: Zebra 4m

If you are in rewind mode and don't rewind the printer will pause while the rewind spool tries to catch up.

Posted on Feb 11, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer


you need to calibrate. hold the feed button down intill it flashes 4 times in a row and the quickly let go. it will feed some labels to calibrate and should stop at the tear off. you also have to set label size in the driver to keep from losing calibration.

May 14, 2010 | Zebra TLP 3844-Z Thermal Label Printer

1 Answer

Zebra Z4M printer error


Did you try disconnecting it from the power for a few hours?

Mar 17, 2008 | Zebra Z4M Printer

2 Answers

I am having problems with Zebra printer MDL#ZM400 skipping if I print 10 lables it might give me 15 lables and 5 of them are blank

Try entering the Menu system and exiting, whilst exiting and instead of saving permanent, cycle around to load defaults. once you have done that make sure the settings are as you need such as Thermal Transfer etc and save permanent. You won't have a problem after that. If you do I would be checking the page setup in the software to make sure it fits the lables.

Jan 23, 2010 | Zebra Z4Mplus Label Printer

1 Answer

Zebra 4m printer. Turn on and pause and error

You have a bad logic bd and it needs to be replaced our repaired.


Dec 20, 2009 | Zebra Z4Mplus Label Printer

1 Answer

Zebra LP 2844 Prints 30 pages of junk instead of a Dazzle mailing

Turn off the printer and place your finger on the green feed button. With the button depressed, turn the printer back on. Let the light flash2.gif (ONLY!) four times and release the button. Printer will cycle through 2-3 labels. Press the feed button one more time.
You've just set the printer back to factory default.

Jul 23, 2009 | Zebra LP 2844 Thermal Printer

1 Answer

I need to know what the difference is between a Z4m and a Z4m Plus.

Mechanically there isn't much difference. Electronically the 4Mplus replaced the 4M giving it more memory, ZPLII capabilities, and the ability to work with new barcodes and fonts that weren't supported by the 4M firmware.

May 14, 2009 | Zebra Z4M Printer

1 Answer

Zebra 4M printer stopping due to error message

The printer is dirty sensor label or no label is calibrated. Turn off the printer and press FEED, CANCEL, PAUSE and turn on, release the keys to advancing the label, and let print be calibrated. Roberto Martinez Mexico

Feb 26, 2009 | Zebra Z4M Printer

1 Answer

I have a Zebra 160s lable printer & i want its installation S\W

You can use software such as Label Matrix, BarTender, EasyLabel or ZebraDesigner (free on

Jan 17, 2009 | Zebra Z4Mplus Label Printer

1 Answer

Zebra 110xi plus not printer strainght across label

* do full manual calibration
* reduce the print speed & try
* set back feed as before instead of default
* try with little big labes

Jul 28, 2008 | Zebra 110Xi III Plus Thermal Printer

1 Answer

Cannot print only one copy; prints the first page only . . . over and over again

Check the menu and got to printing options, it may be that the number of copies got changed, you can set it up to where it can make up to 999 copies!!!!! why that option is on there is a mystery.

Oct 04, 2007 | HP LaserJet 4m plus Printer

Not finding what you are looking for?
Zebra Z4Mplus Label Printer Logo

292 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zebra Printers & Copiers Experts


Level 1 Expert

35 Answers

kenneth njonjo

Level 3 Expert

1575 Answers


Level 3 Expert

57068 Answers

Are you a Zebra Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides