Question about Casio KL60SR Label Printer

2 Answers

What does ERR! mean on the screen and how do you remove it

When I turn on my label printer,E ERR comes up on the screen which I can't get off nor can I get it to print.  Any suggestions.

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 667 Answers
Re: What does ERR! mean on the screen and how do you...

Look here for more information:

Posted on Jan 10, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
Re: What does ERR! mean on the screen and how do you remove it - Casio KL60SR Label Printer Printers & Copiers

Awesome, thankyou!!

Posted on Apr 27, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

When I turn the casio ez label printer on, it say's "ERR!". Then if I push escape, it says "INT?". If I type in any letters and then try to print, it says "ERR!" It...

Take out the tape and spin the drive for the tape. Put it back together and it should work. I hope this provides some assistance to you.

May 27, 2011 | Casio EZ Label Printer

1 Answer

I am getting e020 error switch main off and on again and again

e020 error is of the main fuser unit u can solve it by press *28* then goto copier then function then clear and clear err dc-con err-hist jam-hist and pull both 1st and 2nd drawer now restart and when the screen is ok again restart then on main screen insert both drawers ur err will be removed -tushar sharma -9403343433

Mar 22, 2011 | Canon imageRUNNER 600 Printer

1 Answer


Press the set button,
and then if you get another prompt like INT, press set again.


Feb 23, 2011 | Casio EZ Label Printer

1 Answer

Label for zebra tlp 28844-z with 2 columns not aligned

I'm not sure what you mean here but I'm guessing that you mean the labels are not advancing properly meaning the print is not aligned vertically on the labels. If that is the case, two possibilities:
1. The printer just did not get a good calibration on the printer. You can force a calibration by turning off the printer, pressing and holding on the FEED key while turning the printer on. Keep pressing until the status light flashes once, then let go of the FEED key. The printer will calibrate for the label size.
2. If the calibration sequence does not correct the issue, then it's possible that the gap (horziontal) between the labels just happens to be over the media sensor which is located in the middle of the 4" print width area. If that is true then the labels will never calibrate.

Hope that helps !

Apr 16, 2010 | Zebra TLP 2844-Z Thermal Label Printer

1 Answer

Everytime I print a label it stops short of the

This is an easy printer to fix since there is only one control button. Turn the printer off. Hold the green feed key down while turning the printer on; once the red light begins flashing, let go of the feed button. This will do three things: the printer will calibrate with the installed media, it will print a configuration label and the printer will go into dump mode. Press the feed key again. One more label will come out with with the words "Out of Dump" printed at the top. If the printer still fails to print, remove the ribbon and try the same procedure with direct thermal labels (UPS or FedEx). From there, consult the manual for more troubleshooting tips.

Jan 29, 2010 | Zebra Eltron TLP 2844 Thermal Label...

1 Answer

When you go to print label err!comes up on display

check if printer labels is not stuck or empty.....

Nov 05, 2009 | Casio EZ Label Printer

2 Answers

I have this EZ label printer (says Label IT! and KL 780). It has worked before to make simple labels, but now when I try to print anything-anything at all- 'data error' comes up on the screen. What do I...

Hi. I can help you. Remove all of the batteries. Let it sit for two minutes while it resets. Reinstall the batteries being careful to honor the polarity. Turn it on and you should be up and running. If you still have the problem return it.

Jul 13, 2009 | Casio KL-780 Thermal Label Printer

2 Answers

Cut err

Paper Cutter Error - Guiliteen isnt sliding across the  rail it runs on properly  try lubing rail that cutter runs on with a LITTLE light oil , near front paper exit area

Oct 19, 2007 | Citizen CLP-7201E Thermal Label Printer

Not finding what you are looking for?
Casio KL60SR Label Printer Logo

Related Topics:

969 people viewed this question

Ask a Question

Usually answered in minutes!

Top Casio Printers & Copiers Experts


Level 3 Expert

93738 Answers

Sudeep Chatterjee
Sudeep Chatterjee

Level 3 Expert

3267 Answers


Level 3 Expert

18257 Answers

Are you a Casio Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides