Question about Heavy Machinery

Open Question

Dont know how to tighten chain - Heavy Machinery

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I tighten the chain?


should be a n or somethign that loosens on the side loosen it some, some have a flathead screw that tightens it some dont if not then you have to pull bar and tighten nut

Aug 01, 2014 | Ryobi 18-inch Electric Chainsaw Chain Saws

1 Answer

How to fix my huffy rock it bicycle


Sounds like you may not tightening it down tight. should have about 1/2 play in it. If that dont do it you might look at the sprockets ( bent or missing teeth ) or may need a new chain. Hope that helps you. Good luck. Vern

Apr 30, 2014 | Huffy 20" Rock It Boys Bike, Black/Orange

1 Answer

Dont know how to tighten chain


when its tight you should be able to pull down on the chain and just see the bottom of the middle link pulling on it by hand

Mar 23, 2012 | Garden

1 Answer

New Rancher 455. Ran for a few minutes then tried to tighten chain but adjuster was maxed out (completely tight clockwise). Removed cover, now can't get tension adjusting pin in hole in bar....pin sits...


Ok.. with the cover off the clutch you notice the screw and the pin that is suppose to go into the hole.. with the chain on the bar back the screw until the pin sits in the hole of the bar.. The chain should be lose you will see the chain dangle at the bottom of the bar.. put the cover back on with it lose.. hand tighten the two nuts that hold the cover on. with the bar in hand and you pulling the bar up make sure the two nuts are on tight enough so the bar does not move but dont over tighten it. tighten the screw you will notice the chain starting to move, and start to tighten up.. once the chain is in the grove of the bar grab the chain and move the chain with your hand to make sure you have not over tighten it. if the chain moves freely and is not lose ( you can also double check how tight it is by grabbing the chain below the bar and letting it go if it snaps back into the bar and doesnt hang there you are where you need to be.) tighten the two nuts up on the cover and start up the saw. Run the saw to make sure everything is all set and nothing is lose before cutting.. If the chain never get to tighten up you need a new chain. buy a new chain and follow the steps again. let me know if you have any questions

Jun 19, 2011 | Husqvarna , No.455 Rancher, 20" Gas -...

1 Answer

Loose chain


dont know if you already have an answer for this but... If you take off the chain guard (where the bar connects to the saw body) there should be 2 nuts in line with each other. Losen the nuts and pull the bar forward (away from the saw) and then retighten the nuts. You need to leave a slight belly of slack in the chain so it does not bind. Hope this helps. D

May 25, 2010 | Remington 16" Electric Chain Saw

1 Answer

I have a problem inside of my 2000 Yamaha R6 having to do with the chain assembly. I want to know whats causing the ticking sound that increases when I accelerate. I tightened the chain too much initially...


Sounds like either the chain or sprockets are worn out. If you just put a new chain on old sprockets, that is the problem.
I dont think you could over torque anything to create a ticking sound. The nut that holds the countershaft sprocket (front) on to the transmission shaft would strip if it were over tightened, not click.

Aug 31, 2009 | 2000 Yamaha YZF-R6

2 Answers

49cc kids ATV trouble shooting


in order to tighten your chain you can take a link off which would involve using a grinder, if you dont have one than go to an atv store and ask them to do it. theres a clip on the chain which holds it togther, remove the clip without damaging it than just pop the link off. that will take the chain off. i dont know what type off atv you have so there are probably bolts that hold pull the back end to tighten the chain look for those and if you can find them than tighten them.

for your engine do an oil change and drain out the carborator. if you need more help let me know.

Jun 24, 2009 | Quad 47 cc / 49 cc Pocket Mini Bike...

1 Answer

Chian keeps comming off. Need to know how to tighten


Hi..my name is Keith..i dont know what kind of mower you have..but most models that has a drive chain..to tighten it up..you unloosen the rear axle bolts and pull the rear axel backwards..and then retighten the bolts..but your model may not do that...i hope this helps

Apr 10, 2009 | Garden

1 Answer

Loose chain on Husqvarna 41


first you have to loosen the two bolts on the brake cover . next find the flathead screw located next to the begining of the bar on the inside, facing engine. turning the screw will bring the bar out or in. remember you dont want the chain super tight you want it loose. usually just enough to let the teeth slide a little bit off the bar. once you have the chain were you want it tighten both bolts, and be careful not to move the bar as your tightening. i hope this helps, let me know if you dont understand something i said clearly.

Apr 03, 2009 | Husqvarna Chain Saw 20" Bar

1 Answer

After i use chainsaw the chain loosend


First you loosen 2 bar nuts , then tighten adjuster screw ,this is on cover behind bar nuts or between bar nuts or inside bar on crankcase depending on what model you have ,its also helpfull to lift nose of bar while you tighten adjuster,dont over tighten chain ,then tighten bar nuts

Nov 17, 2008 | Husqvarna Chain Saw 20" Bar

Not finding what you are looking for?
Heavy Machinery Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Heavy Machinery Experts

Bill Boyd

Level 3 Expert

46580 Answers

Tom Chichester

Level 3 Expert

37878 Answers

ray gallant

Level 3 Expert

47630 Answers

Are you a Heavy Machinery Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...