Question about Audio Players & Recorders

1 Answer

Pioneer A 400

Got A400 intergrated amp.can i use it with yamaha DSP E492av processor

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

The DSP-E492 adds-on to a 5-channel receiver, a 2 channel receiver, or a separate system by using either a tape loop (line in & rec out) or the pre-amp/amp couplers that are included as a feature on many products.
In your case you would have to use the tape loop. Hook up by following the general rule of "ins" on one piece of equipment go to "outs" on the other piece of equipment.

Posted on Jan 10, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do i put my behringer inuke 6000 dsp in stereo mode?

Behringer iNUKE NU6000DSP
Stereo mode is set by the DSP processor ( I/O amp mode). The link above will lead you to the manual. On the main page go to "documentation" and to "manual , English". Review and study the functions of the DSP processor. Yo'll nedd to find I/O amp mode.

Jun 02, 2014 | Behringer NU6000DSP iNuke 6000-Watt Power...

1 Answer

How do I connect a Yamaha DSP-E800 amp to a Nakamichi RE-10 amp?

The Nakamichi would be your main channels, so the line out of the Nakamichi would go to the audio processor inputs of the Yamaha, and the original source would plug into the Nakamichi.

Mar 24, 2012 | Yamaha Audio Players & Recorders

1 Answer

Haveing trouble wireing a Pioneer A-400X INTERGRATED AMP, Need the user manual really.Where can i download tthis manual can you help. .

I can't find the manual but there's no real mystery to any generic stereo amp.

OUTs go to INs.

Just about any standard output of an audio device will connect to any Input on theamp EXCEPT PHONO, which is for a turntable.

Tape loops are for tape decks or sound processors like equalizers. When a tape loop is selected the program goes out, gets processed and comes back - all before any volume or tone controls.

May 21, 2011 | Pioneer Audio Players & Recorders

1 Answer

I have a Pioneer DEQ-9200 DSP Audio Processor

are your power wires and your rcas on oppsite sides this may be your problem

Oct 27, 2009 | Pioneer DEH-2000MP MP3 CD AM/FM Car Stereo...

2 Answers

My pioneer a400 hums(very loud) through headphone sockets and speakers, why?

You're probably picking up 60hz AC hum. Through WHAT program sources? You need to isolate the source(s) before an answer can be given. Just phono or any other single source? Bad connection of the RCA cables or bad grounding. Try flipping the AC cord polarity around on the affected component.

May 04, 2009 | Pioneer Audio Players & Recorders

1 Answer

Yamaha Dsp-A1000 5 ch amp Bought a used amp will be hooked to an awia reciever and speakers also have two subwoofers need help to install correctly witch connections to use

if you wanted to use your receiver as your controller and source then try to find out the receivber has got a bridge (jumper) between the pre-amp stage and the power amp stage. if your receiver does not have that, then you can just connect your receiver tape record out to one of your DSP inputs. subwoofers, the DSP has got a sub woofer out connector. you can use that (RCA type) to your sub woofers. put in series because DSP has got only one output for sub. or, you can connect your subs directly to the mains speakers, parallel connections. maybe one sub to your left and the other to your right channel.

Jul 24, 2008 | Yamaha DSP-A1000 5-Channel Amplifier

1 Answer

Auto Shut Off After 3 Seconds...?

either your DSP output stage already damaged or maybe your speakers. have it both chekced for short. or worst both of them. DSP A1000 can drive as low a 4ohms on main channels but how is the power handling of your speakers? are you sure it has not exceeded the capacity of the speakers? or maybe you have over driven the speakers and they are still ok but your amp gut busted due to over drive. If the DSP amp is busted then it is due for replacement of power transistors and drivers. you can not disable the protection circuit. at least the design. it can be disabled by a tech person with a lot of modifications but i wont go for that or it can cause more damage to your equipments. i am from yamaha before and i have made conversions of protection circuits but it is too risky.

Jun 13, 2008 | Yamaha DSP-A1000 5-Channel Amplifier

1 Answer

Pioneer 5.1 dolby surround multichannel processor ?s

You will need extra amp(s) to run 5.1 surround sound using out IP-Bus at the brain to in IP-Bus at the processor and rca output to the multi channels amp(s) and control the surround mode which is automatically activate by the format of the disc. The IP-Bus cables is colored polarized at each end to inter connect all components. Just hook them in series follow the color you may add all the components you have. You can also down load wiring diagrams at Goodluck.

Apr 16, 2008 | Pioneer AVIC-N2 Car DVD Player

Not finding what you are looking for?
Audio Players & Recorders Logo

Related Topics:

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audio Players & Recorders Experts


Level 3 Expert

102366 Answers


Level 3 Expert

5318 Answers

The Knight
The Knight

Level 3 Expert

75025 Answers

Are you an Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides