Question about Maytag Neptune MAH6700A Front Load Washer

Open Question

We have a Maytag Neptune washer Model MAH3000AWW Serial number 25132662UQ. The water pumped out but the spin cycle does not spin, still have excess water on the clothes. We check the fuse box, test the buttons, the belt is ok .you can here it try to run, still no spinning. We opened it up look for any wire problem, we can't see any thing wrong. Please help Jon

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

SOURCE: maytag neptune mah3000aww

volume resistor r-11 on control board

Posted on Apr 29, 2008

Ad
  • 212 Answers

SOURCE: My Maytag Neptune Model MAH3000AWW starts to go

sounds like your control board is going out. when control board is replaced you want to replace wax motor as well

Posted on Jun 24, 2009

duby1990
  • 370 Answers

SOURCE: My Neptune washer model # MAH3000AWW has developed

It sounds like the bearings in the rear outer tub have gone out. This is caused from using powder soap. ( It also happens with liquid sometimes) This is a common problem with front load washers. This is a also a very costly fix. You have to replace the whole outer tub assembly. To get an exact cost just call your local service tech and tell them what your problem is and they can give an idea how much it will be.

Posted on Jun 27, 2009

  • 109 Answers

SOURCE: maytag neptune mah3000aww spin problem

there are 2 wires going back to the board. They connect to a blue harness. Make sure their is continuity thru the harness. It connects to 3 out of balance swithches. Also check to see if lock light comes on.

Posted on Jul 07, 2009

  • 1 Answer

SOURCE: My Maytag Neptune washer won't spin during the spin cycle.

I'm having the same problem...Does it say LR?

Posted on Jul 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My maytag neptune mah3000aww spins slowly then reverses, then spins slowly. will not reach regular spinning speed. What is the problem?


it could be a balance problem. Most machines are programmed to abort fast spin if the drum is unbalanced. This can be caused by too much in there, or possible the contents have clumped together somehow. Try a spin cycle only with an empty machine and see if it reaches full spin

Feb 18, 2015 | Maytag Neptune Washer Door Mah3000aww

1 Answer

Maytag front loader HE washer.


cheak your tube if there is a nail or an object is stuck in one of the holes

Jan 24, 2010 | Maytag MAH6700A Neptune High Efficiency...

1 Answer

MAH3000AWW Does not spin fast enough on spin cycle Clothes are still full of water when done.


hi there ..sounds like your appliance is not spinning at all........(a) check if your drain pump is working correctly..(simply fill water and turn to drain)..(b) possiblity that the clutch drive mechanism is badly worn and needs replaced

regards Sir Galahad

Aug 13, 2009 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Maytag Neptune washer MAH3000AWW seems to backfill after cycle


It could be a leaking water valve. The MAH3000 has two flavors, the earlier model had (2) extra wax motors in the soap dispenser for the bleach and softener controls and the newer ones have the bleach and softener valves integrated into the water valve assembly.

Contact me via the www.neptunehelp.com site and let me know which serial number you have and I can detemrine which water valve you will need.

See www.neptunehelpsong.com for a funny new song dedicated to Maytag Neptune owners explaining the door latch wax motor issue.

Feb 10, 2009 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Maytag neptune washer MAH3000AWW


order the wax motor kit and replace parts from the internet. there are plenty of videos how to do this. it does require minor soldering and a little mechanical aptittude.

Dec 30, 2008 | Maytag Neptune Washer

2 Answers

Maytag Neptune MAH3 series - doesn't spin completely


hi there,

can you supply the model # off your washer please?

Sep 14, 2008 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Won't extract water/Maytag Neptune MAH3000AWW


To be 100 % sure ,do this ,pull the whole face panel forward (remove the 3 screws on top face panel and may have 2 more in the back of the face panel)Once youve pulled the panel forward you will see your control board facing you.Look closely at the circuit board and look for a burnt circuit (CALLED R-11) .iF YOU SEE IT BURNT ,REPLACE THE WHOLE BOARD. I HAVE A COUPLE OF BOARDS AVAILABLE AND WAX MOTORS BUT I'LL NEED THE SERIAL NUMBER FIRST. Either way the board is easy to install the wax motor is a little more difficult.
Please Rate This !!!!

Jun 02, 2008 | Maytag Neptune MAH5500B Front Load Washer

5 Answers

Maytag neptune mah3000aww


re original issue, see if R11 is burned. if so, need to change R11 resistor and associated triac, and probably wax motor so it won't do it again. temporary fix just cut out R11, door won't lock. if your model won't spin that way, depress actuator for microswitch from door wax motor. instructions on web.

Jan 19, 2008 | Maytag Neptune Washer

Not finding what you are looking for?
Maytag Neptune MAH6700A Front Load Washer Logo

163 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

jimorris77

Level 3 Expert

411 Answers

Sheldon Dedek

Level 3 Expert

909 Answers

Bill Long

Level 3 Expert

606 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...