Question about Garmin Forerunner 305 GPS Receiver

1 Answer

No alarms. fast and slow pace alarms as well as distance alarms don't sound.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 84 Answers

See here to what has probably happened...

http://ctorunner.googlepages.com/dismantleforerunner205

Posted on Nov 19, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Security sys light keeps flashing fast


your alarm system needs to be reset, it is indicating that the alarm had been set off by flashing fast...

Jan 15, 2013 | 2008 Chrysler Sebring Convertible

1 Answer

Don't know how to set alarm(s) on a sunbeam digital LED alarm clock model #C38. Can you help??


It's very easy to do. First, make sure the 2 little slider switches on the far right hand side that turn the alarms on and off, are in the "down" off position.
On that clock, just to the right of the large snooze button there are 5 small square buttons. Time, Fast, Slow, Alarm set 1, Alarm set 2.
Depending on which alarm you want to set, hold down that button and simultaneously push either the "fast" or "slow" button to the left of it. The numbers will move forward fast or slow depending on which button you're pressing. Keep an eye on the upper left corner to determine when you've gone past 12 noon - as the indicator for PM will light up.
Keep holding down the 2 buttons until you get to the time you want. Then immediately release the fast/slow button. Your time is set. Do the same for alarm 2 if needed. When finished, flip up the switch for the alarm you want to activate, and you're good to go. Piece of cake! It took me a few minutes to figure it out; but after doing it one time...it's easy. Hope that helps.
I love this old Sunbeam clock. Only problem is the alarm is not very loud and there's no way to raise the volume - short of connecting wires to the speaker and using a powered speaker. Cheers!

Sep 24, 2011 | Audio Players & Recorders

1 Answer

Dnt now how to set my vextra alarm clock, its like its impossible to figure out


  • Hi, I can help you.

  1. Press and hold the "ALARM 1 SET" button
  2. Press the "FAST" button to advance the numbers fast.
  3. When you get close to the number you want then release the "FAST" button and press the "SLOW" button.
  4. Now release the "ALARM SET 1" button.
  5. Repeat the same for alarm 2 holding the "ALARM SET 2" button then stead.
  • Now select Alarm1, Alarm 2 or Alarm 1+2 (for both alarms)
  • Hope this helps and thank you for using FixYa.

Regards, Tony

Jul 27, 2011 | Audio Players & Recorders

1 Answer

Very slow. It starts off fast then almost instantly slows down to a snails pace.


The highest the selected resolution, the slowest is the scanning. Lower the resolution to 200 or 150dpi.

Feb 28, 2011 | Xerox DocuMate 510 Document Scanner

1 Answer

My mazda 3 1.6 diesel on a 2006 will not start up the alarm light on my dash board keeps flashing at a fast pace. what could be the problem?


Mazda 3 diesel

Might seem far fetchted, but try to exchange the light bulb in the glove compartment, it will solve your problem

Feb 16, 2011 | Mazda MAZDA3 Cars & Trucks

1 Answer

Sprinter xl. Batteries old but pass load test. Scooter emits a fast paced alarm when throotle is press. when scooter finally moves it hesitates for a short distance, then drives ok. Brake assembly seems...


Could be a throttle pot problem and /or a speed control pot problem one or both could be dirty or have a bad spot on the pot. If you can live with it use it until you get a flash code trip on the console. Hope this helps

Aug 20, 2010 | Shoprider Health & Beauty

1 Answer

Recording is to fast .


Hi,

If it is a re recordable cassette, you can record again. But if not you cannot actualyy do anything about it.

Regards
Kanu....

Sep 09, 2009 | Video Cameras

1 Answer

Lacks power going up hills


has the fuel filter ever been changed :) this sounds like low fuel pressure.

Dec 24, 2008 | 1993 Subaru Legacy

1 Answer

Mice MS9F96


Sounds like a sensitivity problem.

1) Go to "Control Panel"
2) Go to "Mouse"
3) There should be a slider bar that says "Slow" "Fast" just make it slower an it will slow down the mouse.

If this is only happening sometimes, it could be that your system is bogged down. You could try closing a bunch of programs that are loading on startup or getting more ram for your machine.

Oct 24, 2008 | Computers & Internet

Not finding what you are looking for?
Garmin Forerunner 305 GPS Receiver Logo

Related Topics:

243 people viewed this question

Ask a Question

Usually answered in minutes!

Top Garmin GPS Experts

SHARCNET-USA
SHARCNET-USA

Level 3 Expert

2130 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

TO Lady

Level 3 Expert

638 Answers

Are you a Garmin GPS Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...