Question about GE DBSR453EBWW Electric Dryer

1 Answer

GSM2100G02WW/SH791112B We had a new GE dishwasher installed in February, 2006 so it still should be covered under the original warranty. The problem we are having is; water doesn't drain completely out of the dishwasher after a complete cycle and there appears to be some kind of build up on the inside of the door, possible mold? Is there some kind of cleaner I can run through a cycle to clear this up? Maybe de-limer? Sometimes, the middle cylinder stays in an upright position after the cyle and I have to manually push it back down. I especially want to take care of the standing water inside the unit when not in use and the mold on the inside of the door. Any help would be appreciated.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,314 Answers
Re: GSM2100G02WW/SH791112B

Cleaners are available from Lowe's home depot appliances parts stores etc but it sounds to me like you have a drain problem check your drain line where it attaches to your sink and where it goes into your sink for blockage take off the bottom kick plate and you will see a black solenoid with a silver shaft and a white plastic rocker and spring make sure that the silver shaft moves up and down freely if not replace that seloinoid or call for service

Posted on Jan 09, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Dryer turns, but why doesn't it heat?

The dryer may have been installed incorrectly or the heating element may have suffered early failure. If the dryer is new, it should be covered under warranty.

Jan 26, 2016 | Whirlpool LER4634J Electric Dryer

1 Answer

GE GFDS350ELOWW won't power on

your fuseable safety thermostat mounted on the rear inner wall of the unit open,on a GE these fuses open and it kills the whole units power its under the top cover and to the 2:00 position of the heating element,but if its new call for warranty service it shouldn't cost you anything if its under a year old

Dec 10, 2012 | GE GFDN110ELWW Dryer

1 Answer

Ge profile dryer how do you get to the burner? ge profile dryer tumbles but no heat what is wrong?

Since you have a gas dryer, your problem is probably caused by the ingition panel.Generally, with a gas dryer, there is an ignition device that heats to a specific temperature and this causes the gas to ignite. When this electric ignition fails to work, the gas will not ignite and there will be no heat. I had this happen and had to call a professional. It was a simple matter of installing a new ignition device and it worked perfectly for years. I hope this helps! If it is a new dryer, check to see if this part might be covered under warranty.If this helps solve your problem, please come back to Fixya and rate my advice.

Jul 26, 2011 | GE Profile DPSB620GCWW Gas Dryer

2 Answers

I have a Maytag Neptune Gas Dryer Model MDG9700AWW that has a cracked drum and I was told by Maytag that the drum is no longer under warranty. But told by a Home Depot Associate that the drum is typically...

Not sure if this applies to you, but I do remember back in January 2006 was the date that a large amount of the appliance manufacturers reduced the period of time that their appliances were covered by the manufacture, changes affacted nearly all types of major appliances.
Most went to a all inclusive 1 year parts and labor warranty and you the consumer would be responsible for all failures and labor after the 1 year period which started from the date of purchase. You may have made your purchase smack dab in the middle of the transition period and then details would probably be determined by way of manufactured date.
Good luck !

Jan 19, 2010 | Maytag Neptune MDG9700A Gas Dryer

1 Answer

The door on our GE Pot Scrubber dishwasher - just

You will have to pull the dishwasher out after disconnecting the water pipe and power.

Simply make a new loop on the broken spring or buy new ones from an appliance dealer and reconnect the spring.

Nov 08, 2009 | Dryers

1 Answer

GE oven started flashing F2 only months after purchasing now beep and flashes F 2 and doesnt work, stove top still does not oven though, help!

As long as you did not purchase the range from Sears, (and it is under a year old) you should call an authorized GE servicer to repair the product under warranty. If you contact GE, (for warranty service) they will most likely send out "A & E Factory Service" which may be slow, and there is a lot of negative stuff about them on the net. Call a local authorized GE servicer. Most likely you have a problem with the oven sensor. If you bought from Sears, it did not come with a GE warranty.

Nov 05, 2009 | Dryers

1 Answer

My GE Profile Harmony Dryer purchased in DEc 2006 has had a rip in the stainless steel drum that has now reached about 2 x 3 inches large and now makes noise and does not dry properly.It appears to be...

The tear is due to a poor argon weld of the dryer drum. Check the owner's manual regarding any warranty details. Call the customer assistance line regarding this issue. Have your model and serial number ready for them to assist you. The tear in the drum is causing the blower on the dryer to pull air thru the tear in the drum instead of thru the rear inlet duct which draws the heat into the dryer. This results in abnormally long dry times due to no heat passing thru the drum.

Aug 19, 2009 | GE Profile Harmony DPGT750EC Electric...

2 Answers

THe computer panel is dead. The light comes on inside the dryer when the door is open, but when I press home, power, etc, there is nothing in the computer screen. I bought the dryer 12/29/08. Bonnie...

Hi Bonnie. I see your dryer is under one year old, so don't mess with it yourself. Call a local authorized GE servicer for fast warranty service, or GE at 800-386-1215 to get the standard slower warranty service. (Be sure to have proof of purchase to varify warranty status)

Jul 29, 2009 | GE Profile Harmony DPGT750EC Electric...

1 Answer

Washer thats new and doesnt work

Could be the belt broke or came off. I believe this one has a belt switch, which could also explain the no heat. If this is new, call GE or your local store to have the machine repaired under the manufacturer's 1 year warranty.

Mar 09, 2008 | Dryers

Not finding what you are looking for?
GE DBSR453EBWW Electric Dryer Logo

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Dryers Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

John Tripp
John Tripp

Level 3 Expert

4625 Answers


Level 3 Expert

2963 Answers

Are you a GE Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides