Question about Hotpoint Aquarius WD640 Front Load Washer/Dryer

1 Answer

Hotpoint aquarius wf 620

Hi if anybody can help machine flashing f-01 if any body has any ideaswould be grateful.

Thanks Will

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 196 Answers
Re: hotpoint aquarius wf 620

A fault code of F-01 normally refers to a short circuit in the control board. The best way to find out is to gain access to the service sheet located inside the machine.

Look at the back of the machine. Along the top there should be 2-4 screws the hold the top in place. Remove these screws and pull the top backward to release it from the front. Remove the top. The service sheet should be taped to one of the support arms.

Posted on Jan 09, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Wash enhance is flashing program not advancing

iv got a hotpoint aquarias wf 514 all lights are flashing whot do i do

Jan 03, 2011 | Hotpoint Aquarius WMA42 Front Load Washer

3 Answers

Hotpoint wf740 aquarius 1400 v noisy banging during spin = dust

It could be a broken drum restraint spring, or a worn or broken. or loose shock absorber.
To check the springs, remove the top cover, and you will see the springs.
Another possibility is the concrete weight could be broken or loose.
You need to remove the lower rear panel of washer to check the shockers and concrete weight.
Please rate my solution.

Jan 31, 2010 | Hotpoint Aquarius WF000 Front Load Washer

2 Answers

Control panel lights ALL flashing on hotpoint aquarius washing ma

my lights are all flashing on my control panel, its takes water in then pumps out straighaway doesnt wash or spin i have changed the brushes so i know it isnt that please help it only about 3 years old

Dec 06, 2009 | Hotpoint Aquarius WMA42 Front Load Washer

1 Answer

Error code f-01 on hotpoint washer dryer aquarius model wd 640

f-01 means there is a motor problem.
may be the motor and/or the circuit board that controls it.

Jan 05, 2009 | Hotpoint Aquarius WD640 Front Load...

4 Answers


The lights are set off by the balance sensors.And if your balance sensors are  stopping    it from spinning than you first have to make sure the washer is level.You  could have bad Shocks and a bad electronic control board,.                                    

May 05, 2008 | Hotpoint Aquarius WF000 Front Load Washer

3 Answers

Hotpoint Aquarius wf 541

Check your drain pipe behind. This is supposed to be approx 3 feet above ground level; then the hose goes into the stand-pipe without being too tight. If this does not work, click "thanks for trying"; your prob will be back for someone else to solve.

Jan 14, 2008 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

Hotpoint WD440G


Aug 27, 2007 | Hotpoint Aquarius WD63 Front Load...

Not finding what you are looking for?
Hotpoint Aquarius WD640 Front Load Washer/Dryer Logo

156 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts


Level 1 Expert

5 Answers


Level 1 Expert

47 Answers


Level 3 Expert

2963 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides