Question about Cadet Manufacturing 67508 Coil / Ribbon Compact Heater

2 Answers

Cadet In-Wall Heater - Red Light is on

What does it mean when the red light is on on my cadet in-wall heater? What can be done?

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

  • Contributor
  • 5 Answers

The light is actually to tell you that the safety has been activated. This is usually an indication that the heater is dirty and needs to be cleaned. Turn the heater off at the breaker and take the grill off. Use a hairdryer or a shopvac on the exhaust side and blow the heater clean. If this doesn't fix it the the heater will need to be replaced. The light indicates that you have an "X" model heater.

Posted on Jan 19, 2015

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 625 Answers

Means that the element is ON

Posted on Jan 10, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My cadet wall heater wont turn off


My cadet heater was doing this so I pulled it off of the wall and saw that the two wires coming from the thermostat portion had melted out of their insulation and were crossed. The heat is of some concern, but for now I just wrapped them in electrical tape to insulate them better against melting

Mar 11, 2012 | Cadet Manufacturing Built-In Wall Heater

1 Answer

I just need a wiring diagram---with a thermostat-- for a cadet FX-152 , 240 volt ,1500 watt wall heater


grainger has them- home depot. wire is easy wire one side straight to 1 wire on in coming power the other side use your thermostat to break curcit ie wire into stat out of stat to voltage

Jan 15, 2010 | Cadet Manufacturing CADET SL Series Small...

2 Answers

There was an electrical smell when the heat was on


Could be ,to be certain take it out the wall and check

Mar 07, 2018 | Cadet Manufacturing 67508 Coil / Ribbon...

2 Answers

Cub cadet lt1040. won't start. new battery. making a cliking sound when you try to start it.


I had the same problem the starter was the problem, found the stater will engage by itself not sure why but think it could be the wireing, or a swich. also check the solenoide it could be bad if the starter is bad.

Sep 26, 2009 | Cadet Manufacturing CADET SL Series Small...

1 Answer

Cadet wall heater


Since I don't know what model of heater you have there might be a reset button to reset or an over temp switch (button sensor with 2 wires going to it) that needs to be replaced. You might check the recall list to see if this one has been recalled and should not be used.

Sep 11, 2008 | Heating & Cooling

1 Answer

Not a cadet but a King


shut off the breaker, then, remove the front grill. look for a device about the size of a nickel. could be fastened to the upper case. this is called a klixon overload. there are numbers stamped into the side of it. one of these are either temperature or an amperage value. get a replacement from an electrical supply house. it is probably blown. it is in series with the element. its purpose is to open [then reset] when an increase in current is evident. it is a bi-metal device - two dissimilar metals that bend at different rates when current is applied to it and opens a set of contacts.

Nov 12, 2007 | Cadet Manufacturing 67508 Coil / Ribbon...

Not finding what you are looking for?
Cadet Manufacturing 67508 Coil / Ribbon Compact Heater Logo

Related Topics:

1,881 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadet Manufacturing Heating & Cooling Experts

Paul Carew

Level 3 Expert

3336 Answers

Mack Baxter

Level 3 Expert

383 Answers

Marvin
Marvin

Level 3 Expert

82322 Answers

Are you a Cadet Manufacturing Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...