Question about Vizio L32 32 in. LCD HDTV

1 Answer

I have a dark shadow down the right side of the screen, the outer edge is very straight and the inner edge of the shadow fades toward the center. What would cause this and can it be fixed?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Vizio Master
  • 1,210 Answers

Could be an LCD panel needs replaced.....very pricey, unless it is still under warranty!

Posted on Nov 16, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 57H84 toshiba. My screen is dark. You can only watch it if he screen had been broken but was replaced. Except for the third screen which we did not realize there was. Is this a screen issue or...

Outer if 3 screens is just protective and inner two are critical----they focus and direct the light from the picture tubes to the front of the set---yes if missing one of the two inner (usually taped together) it will not be bright or look right and both have a inner and outer side to them.

Nov 02, 2012 | Toshiba Televison & Video

1 Answer

Solution to think square by pressman and crimes games 17 pieces fit together to make a square it's killing my brain Trying to work this out can you help??? Desperate for sleep, Erica :)

All thethe pieces go in atthe a 30 degreemin angle.

Triangles go around outside with longest sides going against the outer edge, shortest sides pointing counter clockwise, and 2nd longest sides facing the middle. Big triangle points toward little triangle.

5 little squares go in the middle to make a cross. Turn it 30 degrees so straight sides of crossthe are parallel with inner edges of the triangles around the outside.

The big odd pieces go between triangles and cross.

May 09, 2011 | Video Game Consoles & Games

2 Answers

It is a double oven, but I want to eliminate the lower oven... so, I am looking for an electrical plan so I can find out how to disconnect the lower oven... and only install the top part.

•Step 1
Open the oven door to the half open position. Locate the hinge on each side of the oven door toward the bottom. The top center of each hinge has a hole. Insert a nail or screw into the empty hole on each hinge to prevent the hinge from closing inside the door rail after disconnecting from the oven.
•Step 2
Grab the sides of the door with your hands and lift straight up to disengage the hinge from the door. Push down slightly on the top of the door to release it from the hinges. Pull the door away from the oven and place it on a flat surface with the door handle toward the floor.
•Step 4
Using a Phillips-head screwdriver, remove the two screws at the top of the inside door panel that secure the inner door panel to the outer door panel. Loosen and remove the three screws on the bottom edge of the oven door with the screwdriver. Lift the inner panel away from the outer oven door.
•Step 4
Loosen the two screws that secure the door handle to the outer door panel. Lift the outer door panel slightly to pull the handle away from the door.
•Step 5
Remove the screw at the top and bottom of the side hinge rails with the screwdriver. The hinge rails mount to the outer door panel and the inner panel sits between the rails. Lift the hinge rails off the outer panel.
•Step 6
Lift the inner door glass straight up out of the outer door panel. Stand the outer door panel up on its bottom edge. Pull the top trim off of the door panel and outer glass. Hold the top of the glass panel and pull the two side trim pieces away from the outer panel. Pull the outer glass away from the outer pan.
once it comes out you can do what u want.

Jul 27, 2010 | Ovens

1 Answer


I would check for dust particles before I attempted any type of repair on the unit.

Dust particles will appear as dark spots that are larger than the size of an individual pixel. It must first be determined if the particle(s) are on the LCD panels or the screen.

May 27, 2009 | Sony KDF-E42A10 42 in. LCD Television

1 Answer

Can't get rear license plate lamp covers off

The manual says switch off the lights and disconnect the battery. Then "Open trunk lid. Press and slide license plate light outward and remove". The photo shows that there is a clip on the side of the light away from the center, and a notch that fits the body on the side towards the center. So what you are doing is pushing the light holder towards the side of the car far enough to compress the clip and get the notch past the metal, then the inner edge of the light hold should lift out. To install, just put the notched end in first and the press the outer edge until the clip snaps into place.

May 10, 2009 | Audi TT Cars & Trucks

1 Answer

I can't get the radio out of the dash of my 1990 740 turbo sta wa

In order to remove the radio, first pull off the the radio knobs (tuning and volume, etc.) there is an outer knob, and an inner ring on each side, first pull off the outer knob....pull straight out- it's tight but it will come off with some hard pulling...then slide the inner ring straight off. Do the same to the other side. Use a flashlight, and look thru the knob hole, between the knob shaft and the outside edge of the knob hole, and you will see and you will see a silver spring clip. Use a slim screwdriver or pen knife to gently pry the end of the spring clip toward the center of the radio, as you try to pull the radio towards you. It will come out about 1/4 of an inch. Then do the same thing to the other side, and the radio will easily slide right out. Good luck.

Mar 29, 2009 | 1990 Volvo 740

1 Answer

1996 toyota corolla side marker light removal to install new one

Open the hood. Observe the "tab" on the driver side inner fender, above the corner of the headlamp, outer edge. Remove the screw. Pull the lamp assembly straight forward, towards you. If it has never been out, the lamp will be tight. There are 2 locking pins inside the fender that need to be defeated, you just have to grasp the back side of the lamp (closest to the driver door) and pull it straight towards the front of the car, NOT sideways.

Dec 23, 2008 | 1996 Toyota Corolla

1 Answer


check your tft backlights for burnt or breakage .

Sep 29, 2008 | Philips Magnavox 15MF400T 15 in. LCD...

1 Answer

How do I remove the outer protective screen on my Mitsubishi WS-55315?

There are trim pieces around the edges that can be removed by sliding a knife underneath and lightly prying. They should remove fairly easily, don't force them as they may break. Use the knife on the cabinet side and pry toward the center of the screen.

The tear on the inner screen may be best left as is.

lexan would be better than plexi as it is tougher, but try to get anti-glare if possible. Anti-glare plexi would be better than regular lexan.

Feb 17, 2008 | Mitsubishi WS-55315 55" Rear Projection...

Not finding what you are looking for?
Vizio L32 32 in. LCD HDTV Logo

1,011 people viewed this question

Ask a Question

Usually answered in minutes!

Top Vizio Televison & Video Experts

The Knight
The Knight

Level 3 Expert

74251 Answers

Level 3 Expert

749 Answers

Computer Repairing
Computer Repairing

Level 3 Expert

14641 Answers

Are you a Vizio Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides