Question about Uniden Cordless Phone

1 Answer

Power went out and when it came back on our phone says searching or out of range?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 108 Answers

Sounds like a possible loss of SYNC with the base. unplug both, and at the same time remove batteries and then let sit for a hour or so. install battery first on cordless phone and then plug in base, if this continues you might have had the phone hit by a power spike on resuming power and it may have caused a more internal board or component failure.

Posted on Nov 16, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My handset is display only searching, I cannot make or recieve calls & it is just flashing 88


when I press talk I get connectin9..handset out of range..searcgin9
when I press end I get Searching

Jan 30, 2013 | Uniden DECT 6.0 Cordless Phone

2 Answers

Handset says searching


Searching means its searching for a signal. If the phone cant contact the base it will say searching. Make sure the handset is in range of the base and the base is connected to the power.

May 16, 2012 | Uniden DECT 6.0 Cordless Phone ID

1 Answer

Both of my GE Dect 6.0 cordless phones, model #5-2811 say out of range or searching...out of the blue. How do I get my dial tone back???


Unlplug the power to all lines for 5 minutes, while waiting disconnect, inspect and clean the phone cords. Insert the phone cords back into the devices after 5 minutes of ALL devices being unpowered plug them all back in, Set each of the phones on the main receiver to "sync" them.

May 13, 2011 | Uniden Cordless Phone

1 Answer

Electric range heard a loud bang then it went dead


I WOULD DISCONECT THE POWER AND REMOVE THE BACK PANNELS AND LOOK FOR A SHORTED WIRE OR A BURN MARK ON THE BOARD. ALSO CHECK WHERE THE CORD ATACHES TO THE STOVE. GOOD LUCK!
ERIC

Jan 17, 2010 | Kitchen Ranges

1 Answer

SabBath mode


Try unpluging it for about 5 mins. and plug it back in. when the power went off it was a power shurg.

If that don't work. It may have burnt the curict board. Ken.

Sep 21, 2009 | GE Profile Spectra JGBP85 Gas Kitchen...

1 Answer

Searching....


The problem of searching.....

After trying all the technician's suggestions had failed; I disconnected the base to return it to the store for replacement. Then I decided to try disconnecting and reconnecting power and phone line, placed handset back on base and the phone reset itself and is working fine...

Recap:

Disconnect power and phone line from base for about 30 seconds and reconnect both power and phone line to base and place handset back on base; it should reset...

Linda

May 05, 2008 | Uniden DECT 6.0 Cordless Telephone...

1 Answer

All of the sudden the phone just stopped working. It says 'out of range'.


remove battery from handset then unplug base from power supply. Reinstall battery in handset then plug base back in to power.It worked for me.

Dec 16, 2007 | Uniden DCT756 Phone

3 Answers

GE dect 6.0 cordless phone bought at walmart


We had the same problem.

"Our phones worked fine for two weeks but now you can not dial out
and when someone calls us they can't hear we say. The line still works
fine with our old phone1.gif."

To fix the problem, I simply unplugged the base AC plug from the outlet, waited about 15 seconds, and then plugged it back in. Both handsets said searching on the display and then handset names returned to the display as originally programmed. The phones returned to operation as normal.

Devo

Nov 14, 2007 | GE 28111 Cordless Phone

1 Answer

All lights on the touch panel are flashing and a continous beeping sound


bosch 700 series range. So far unplugging the range and waiting several minutes to plug back in reset everything like rebooting a computer.

Dec 19, 2006 | Bosch HGS435UC Gas Kitchen Range

Not finding what you are looking for?
Uniden Cordless Phone Logo

Related Topics:

217 people viewed this question

Ask a Question

Usually answered in minutes!

Top Uniden Lands Phones Experts

kakima

Level 3 Expert

102366 Answers

k24674

Level 3 Expert

7993 Answers

Cindy Wells

Level 3 Expert

5103 Answers

Are you an Uniden Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...