Question about Netopia 3347W-KIT ADSL Wireless Gateway, plus Wireless PC Card Router (3347WKIT)

1 Answer

Curtis need to have nat capability and let a web-server function at the same time.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that has over 10 points.


    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 17 Answers
Re: Curtis

Run NAT on your router
then lets say your LAN (router)
and your pc (webrouter)

then use Port Forwarding on the router to:
Foward port 80 (www) to


Posted on Jan 09, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

How to config my belkin n300 to change nat to open in xbox live

Belikin has one DMZ IP option in the web admin.

Go to Portforward dot com for step by step instructions. Also refered to as virtual servers on some routers.

Dec 29, 2012 | Belkin Surf N300 Wireless N Router

1 Answer

I need an open nat on my sagem 1704 router for ps3 game mw3

I did it with Xbox.
Manually configure your console to have a specific IP address. I set my XBox to, with the subnet of and the gateway of
Then (on a computer) I opened my web browser and went to the address:
The name and password are both: admin
I clicked Adcances Settings, then NAT, then Virtual Servers.
I created a virtual server, named it, gave it the IP address of my console, and opened up the appropriate ports.
Once I saved it, it worked fine.
How to configure Windstream st 1704N dsl modem router for Xbox live NAT

Apr 02, 2012 | Routers

1 Answer

Where is your NAT configuration to open and close it for this router? I've watched YOUTUBE videos on where to find the NAT section and I don't have one. Help me I just want my PS3 to have a type 2 NAT so...

Belkin uses the term "Port Forwarding" in the "Firewall" section of the configuration web pages instead of the term "NAT".
For each port that you need to forward to the PS3, create a separate entry in the "Virtual Servers" section.
If that's too much work, then determine the private IP address of your PS3 and add that address to the DMZ for your router. The DMZ settings area is also in the "Firewall" section of your router configuration web pages.
For more information, go to the Belkin support web site and select "G" for "1" and "F5D9231-4" for "2" and the select either V2000 or V1000 depending of your router version (see the bottom of the router) and download the user manual.
While you are there, check whether there is a firmware update for the router available.

Dec 30, 2010 | Belkin F5D9231-4 Router

1 Answer

Need to allow a telnet session thru a speedstream 5660 modem/router having a public ip and allow it to connect to a private ip on the internal LAN. how do i accomplish this?

According to the user manual:
Page 16:

HTTP Web-browser Access

Most HTML browsers can be used, though Internet Explorer 4.0 or Netscape 4.0 are recommended. IE 2.0 and Netscape 2.0 and their predecessors are not supported. The HTML interface can be used to access the LAN (or WAN) IP address or it can be used with FTP to upload and download files to and from the router.

To log on to the modem via HTML:

1 Bring up your favorite web browser.

2 Enter the Ethernet IP address of the router ( or Speedstream) in the "Location" or "Address" area where you enter web page addresses.

3 Refer to "HTML Web Interface" on page 20.

Page 20:

HTML Web Interface

The HTML interface for the router first displays a page showing the current configuration of the router. The first page also provides links to the following functions:




Advanced Setup

Leads to a more detailed interface with several links that allow more in-depth configuration of functions available on the router. This interface provides the following links:

Configuration Procedures

Status and Statistics

Command List

This is where the user manual ends. I would suggest clicking "Configuration Procedures" and find the section for configuring Network Address Translation (NAT).
In that section (if it exists), you'll want to provide the private IP address of the computer running the Telnet server and forward port 23 to this IP address.
If NAT capabilities do not exist, I would consider changing the router to Gateway mode (described in the user manual) and buying your own router to handle the NAT firewall.

Dec 29, 2010 | Efficient Networks SpeedStream 5660 Router

1 Answer

How do i forward a port i want to play call of duty black ops but i cant find an online game, the game website says to forward these ports, TCP [80] UDP [88, 3074, 22728, 33233] but i dont know how to...
Server List (Port Forwarding) NQG_025 With NAT enabled, the IP addresses of nodes on your LAN are private since they are hidden from the Internet. IP Servers let you pass specific types of network traffic through the Netopia router's NAT interfaces. Once configured, selected types of network traffic, such as FTP requests or HTTP (Web) connections, will be forwarded to a specific host or server behind the Netopia router. Please Note: From the LAN (Local Area Network), you will also be able to access the servers that are responding to requests from the internet, but only using the internal private IP address. Access via the public IP address is not supported from a local ethernet connection. If your ISP is routing you multiple public IP addresses, you can also configure the router to forward all ports in one public IP to a designated private IP address on your LAN via Easy PAT List entries. For those instructions, see Quick Guide NQG_024: IP Mapping (Address Forwarding).
Please Note: If your router is currently running Netopia Residential Firmware with a web "GUI" configuration menu, this technote is not applicable to you. Most 3300 Series Netopia Gateways can be upgraded to Enterprise level firmware. Click Here! to purchase the upgrade key.
Related documents: NQG_039 NAT and the Basic Firewall
Firmware References:
  • v8.2 R1 (and up) - 3300 Enterprise Series
  • v5.3.7 (and up) - 4000 Series
  • v4.8.2 (and up) - R-Series

Before You Start
Telnet into the Netopia router's Main Menu at (if using the default IP setting). If your network has a different IP addressing scheme, modify this accordingly. Click Here! for instructions on using telnet and Hyperterminal (serial connection).
Login with the user name and password. The Superuser login is required to save changes. If you are unsure of this, contact your network administrator.
Don't forget to press the Enter key to save any entries. Hitting the back space, delete or tab without first hitting enter will undo any changes.
The Esc key will take you back towards the main menu screen.
Once you have completed your configuration, you should reboot the Netopia to save and apply your changes.

The Netopia Main Menu Interface

Server List Configuration

  1. From the Main Menu of router console screens, go to Quick Menus, and select Network Address Translation.
  2. Select Show/Change Server List.
  3. Select Easy-Servers.
  4. From the Show/Change NAT Server List screen, select Add Server.
  5. Select Service and the service and port you want to allow. If your service and port are not available in the pull-down menu, select Other. Selecting Other will allow you to enter a specific service port or a range of ports since fields are provided for both a First Port Number and a Last Port Number. To allow a specific service port, the First Port Number and Last Port Number should be the same. Select Okay.
  6. Next, enter the Server Private IP Address, or the private IP address of the host/server you are forwarding the service to, and the Public IP Address you want to associate with the same host/server. This value can be left set to if you are using the WAN IP as the Public IP address. Note: If your ISP is routing you multiple static IP addresses, other then the one used for Internet access, you may create more than one server for specific service as long as all servers have a different Public IP Address specified. For example, with two web servers on your LAN you would need to create two Server List entries for TCP 80 (www-http). Since each specific port (service) can only be mapped once using any given Public IP Address, a distinct public address must be used for each TCP 80 server list entry. It is not necessary for you to specify more than one Local WAN IP Address or Public IP Address in your router's configuration. As long as you are connecting to your ISP via a public IP address used for NAT, they are responsible for routing all other IP addresses via that connection.

You have now configured your router for TCP/UDP port forwarding. If you have a switched connection (ISDN or Analog), you will need to either disconnect and reconnect your Internet connection, or restart your router for the Nat Server List changes to take effect. If you wish to filter traffic for your static IP mappings, please see the following Netopia Technote:
NQG_039: NAT and the Basic Firewall

Nov 12, 2010 | Netopia CAYMAN 3387W-ENT CABLE/DSL...

1 Answer

Xbox restrict chat . csomeone told me a NAt setting needs to be changed. I have a netopia 3347 router help children are screaming

Before You Start
Browse into the Netopia's web interface at (if using the default IP setting). If your network has a different IP addressing scheme, modify this accordingly.
Login with the admin user name and password. Admin login is required to save changes. If you are unsure of this, contact your network administrator.
Once logged in, click on the Expert Mode link in the left-hand side menu (if that link is visible). In the Expert Mode Confirmation screen click on Ok to continue. This menu bar will be visible at the top of your screen if you are in Expert Mode.
Remember to click the Submit button to save any entries. Hitting the back button without clicking Submit will undo any changes.
Once you have completed your configuration, click on the 3000save.gif symbol in your upper right hand corner to validate the changes. Then click on Save and Restart.
3000home.gif The Netopia Web GUI Home Page in Expert Mode (Firmware v6.3 and later)
Configuration for NAT Default Host
  1. Click on Configure in the upper Menu bar.
  2. Click on Advanced.
  3. Under the NAT heading, click on the Default Server link to Set up NAT default server options. 3546defsrvr.gif 3546dfsrvrmenu.gif
  4. "Check" Enable Default Server.
  5. When the Default Server box appears, enter the NAT Server IP Address for the specified internal host to which NAT traffic should be directed.
  6. Click on Submit.
  7. Click on the 3000save.gif in the upper right hand corner. This will validate that the settings are legal for your network.
  8. If you get Validation Passed, click Save and Restart in the menu. If it doesn't validate the change, a message will indicate the reason. It must be corrected before the configuration change can be applied.
  9. This completes the configuration of the Netopia for NAT Default Host.
  10. the nat server ip is the one you type into the browser were you had to type in your admin log in

Jul 30, 2009 | Routers

1 Answer

Cant create game server due to NAT settings

Make sure that you are using 1:1 NAT and not dynamic NAT, but more likely its a configuration issue. Some game servers like private WoW servers or Armagetron work better when the configuration file is setup with the computers IP and not "localhost" which is technically and not Nat'd.

Jan 14, 2009 | Linksys Wireless-G WRT54G Router

1 Answer

Change NAT to open

The ports should be opened only in the router not in the, go to a working pc..

To allow traffic from the internet to enter your local network, you will need to open up ports or the router will block the request.

Because our routers use NAT (Network Address Translation), you can only open a specific port or ports to one computer at a time. For example: If you have 2 web servers on your network, you cannot open port 80 to both computers. You will need to configure 1 of the web servers to use port 81. Now you can open port 80 to the first computer and then open port 81 to the other computer.

  • Step 1 Open your web browser and enter the IP address of your D-Link router ( Enter username (admin) and your password (blank by default).

    Step 2 Click on the Advanced tab at the top and then click Virtual Server on the left side.

    Step 3 Check Enabled to activate entry.

    Step 4 Enter a name for your virtual server entry.

    Step 5 Next to Private IP, enter the IP address of the computer on your local network that you want to allow the incoming service to.
  • to check ip in your pc.. go to start menu click run.. type cmd and hit ok
  • in the black window enter ipconfig and hit enter, you will find the ip address

    Step 6 Choose Protocol Type - either TCP, UDP, or both. If you are not sure, select both.

    Step 7 Enter the port information next to Private Port and Public Port. The private and public ports are usually the same. The public port is the port seen from the WAN side, and the private port is the port being used by the application on the computer within your local network.

    Step 8 Enter the Schedule information.

    Step 9 Click Apply and then click Continue.
  • This would fix your problem..

    Nov 15, 2007 | D-Link Wireless Cable/DSL 802.11G Router...

    1 Answer

    How do I open ports in the Virtual Server?

    You need to forward the ports used by the application to the server running the application in the Virtual Server, which is present in the router's management screen, as follows. 1. Open your web browser, type in the router's IP address (standard: '') and press enter. 2. Click on Login, Advanced Setup, NAT, Virtual Server. 3. Enter the port details and enable it as follows: Private IP Private Port Type Public Port 192.168.2.x xxx TCP xxx 192.168.2.x xxx UDP xxx

    Feb 19, 2006 | SMC Barricade 7004 Router

    1 Answer

    Nortel Contivity VPN client?

    Nortel Contivity will work with the your D-Link router, however its functionality depends on the authentication type (AH will not work), NAT compatibilty mode, and disabling keep alives on the server. Contact your Network Administrator to find out how your VPN is configured. Step 1 Verify that you are using the latest version of firmware on your router. Step 2 Login to the Web Management for your router by entering its IP address ( in your web browser. The default username is admin, and the password is blank. Step 3 Click the Advanced Tab to access the Virtual Server Settings. There is a list of pre-defined Virtual Server Rules towards the bottom of the page. Find the IPSec Rule. Click the pen and paper icon to edit its settings. Enable the rule, enter the IP address of the computer attempting to connect to the VPN in the Private IP field, then Apply the changes. Step 4 Create a new Virtual Server entry. Name the Virtual Server, "NortelVPN". Enter the IP address of the computer attempting to connect to the VPN in the Private IP field. For the Protocol Type, select Both. Enter 9550 for both the Public and Private Ports. Set the Schedule to always, then Apply the settings. Step 5 Access the Tools Page, then click the Misc button. Disable IPSec Pass-through, then click Apply. If the VPN Server is properly configured to work with clients behind NAT routers you should be able to connect to the VPN.

    Feb 16, 2006 | D-Link Express EtherNetwork DI-604 Router

    Not finding what you are looking for?
    Routers Logo

    Related Topics:

    63 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Netopia Routers Experts

    Douglas  Erikson
    Douglas Erikson

    Level 2 Expert

    62 Answers

     C. Dante
    C. Dante

    Level 3 Expert

    623 Answers

    Martin Murray

    Level 3 Expert

    1614 Answers

    Are you a Netopia Router Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides