Question about Craftsman 10" Table Saw

Open Question

I have a craftsman table saw model # 137.218780 Seriel # RCW 4061 ... I need Adjustable cuting guide.. Ceter plate for the saw blde Need aprice on these items...

Posted by on

  • David Ford
    David Ford May 11, 2010

    I would recommend going to Searspartsdirect.com and typing in your model number for a complete breakdown and price list for this tool. You can also order parts online thru this site. Let me know if you need more assistance and if I have helped you with your request would you please rate this response accordingly. Thank you.

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
rowdy45176
  • 2176 Answers

SOURCE: Looking for owners manual Craftsman table saw 101.02141

I tried their site and they say no parts available for that tool, They suggest that you call them direct and I have a phone number at 1-800-252-1698 and they might be able to help. Good luck

Posted on Mar 30, 2009

Ad
  • 474 Answers

SOURCE: Lost Manual

try craftsman.com

Posted on Oct 31, 2009

agent91
  • 2100 Answers

SOURCE: Craftsman 10' table saw model # 137.248830 will not start

Reset button on the motor, push till it clicks. How about the breaker? What kind of switch is it? Is it plugged in? Check this stuff out. Hope it helps.

Posted on May 09, 2010

  • 520 Answers

SOURCE: Have an older Sears Craftsman 10" Table Saw, model

you should be able to order one from sears. another place to look is ebay. the round plastic thing is to mark with pencil the cut of the blade. put in your sliding miter Gage set at 90 deg. put a piece of wood on it, push forward and cut the wood then slide back and mark the wood position on the plastic. that's the point where your blade cuts

Posted on Jan 03, 2011

Testimonial: "Thank you very much, I'll try Sears first and see if they can help. Since it's an older saw, they haven't been much help up to now."

jyackle5
  • 8197 Answers

SOURCE: I have a craftsman model

Don't have all the answers you want, but may be able to help with the dado question. The 137 generally points to Rexon-Tradesman. A brand sold here by Lowe's.

My table saw is 137.248800 which will Not accept an 8" dado blade set.

You may have purchased the 8" dado set. Try the 6" size, if your saw has a 5/8" arbor. My dado set is the Freud (SD206) carbide version. My saw will accept only up to 1/2", maybe 9/16" dado setup.

The cabinet saws typically use the 8" dado set, capable of up to 3/4".

You should also be able to get the parts that you need at Sears.

Posted on Jan 31, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need a fence for my model # 113221770 craftsman table saw


look at the uni9 fence by delta or the better yet from general. Delta is part poor. retrofit shouldn't be too much of prob.

Dec 28, 2013 | Craftsman Sears 10" Table Saw Extension...

2 Answers

We need a downloadable user's guide for this product. Thank you.


Go to: http://www.searspartsdirect.com/partsdirect/user-manuals/113221740-Craftsman-Parts-Saw-Parts-manual.

Sep 23, 2013 | Craftsman Sears Table Saw Manual Model...

2 Answers

Does the bolt turn R or L also does it take a special tool. I have had this saw for 28 years and my guys changed the blades I fear they lost the tool. Also will a 10" blde work it has a 71/4 now


The bolt on your saw blade turns right. Hold a block of wood against the blade so the bolt can turn. You can use a adjustable wrench if it will fit. Otherwise see if an open end wrench will fit. The 10" blade will only work if the saw was designed for a 10" blade and there is enough clearance.

Mar 14, 2011 | Craftsman Saws

1 Answer

I have a crftsman table saw mdl # 137228210 I purchased the saw used. I need a rip fence . the guides are allready there. any help would be appreciated


There's an exploded parts drawing and parts list at the link below. This may be useful to see what the fence is supposed to look like. It's not listed as an assembly, just a surprisingly long list of parts that would cost a fortune - if they were all available. Maybe you can find one on ebay. Barring that, you can always just clamp a board to the table to rip with - the hard part is getting the makeshift fence to be parallel to the blade. To do that you can use an adjustable square and measure from a miter slot in the table to get a quick and straight setup. Good luck.
http://www.searspartsdirect.com/partsdirect/part-model/Craftsman-Parts/Saw-Parts/Model-137228210/0247/0744600/P0104056/00001?blt=06&prst=0&shdMod=137228210#Partslist

Feb 09, 2011 | Craftsman 10" Table Saw

1 Answer

Need electric motor for model #113241680. what is the rpm and horse power.


here is the sears parts for your saw
http://www.searspartsdirect.com/partsdirect/part-model/Craftsman-Parts/Saw-Parts/Model-113241680/0247/0744600?pathTaken=

looks like they dont sell the motor any more. as long as you have the spec plate on your motor you should be able to match up something from a parts house or anyone that sells electric motors. in my area its Granger

Dec 28, 2010 | Craftsman 10" Table Saw

1 Answer

I have a craftsman professional model 10" cabinet saw, 3 yrs old. Been working great, just noticed blade is not square to miter guides. Where is adjustment Clfavia@yahoo.com


you can try going to managemyhome.com with your model number for an owners manual for the adjustments that you need. Let me know if you still need assistance.

Aug 08, 2010 | Craftsman 10" Table Saw

2 Answers

I have a craftsman table saw model 113.27870. I need a table insert for a dado blade. I looked on the sears website and it said parts for this saw are no longer available. Will a table insert for a newer...


Maybe you could try using the outline of the regular insert to cut a new insert out of a piece of polycarbonate (lexan) or ABS plastic. The clips that hold my dado insert barely hold it in place on mine, and I've seen other saws that use plastic.

Aug 02, 2010 | Craftsman 10" Table Saw

1 Answer

Adjusting the saw blade for exactly 90 degrees on an old craftsman 10 " radial saw


If the saw is adjustable for angle we usually use an engineers square against the blade to get it upright and then you may find an adjustable stop or stops somewhere so you can set the position ready for the next time you need to set it.

Jun 03, 2010 | Craftsman 10" Table Saw

1 Answer

Need a replacement motor for 1972 craftsman jointer


went to Sears site and no luck most parts are discontinued. So maybe try Grainger with the information from the data plate on the motor for a replacement or check in yellow pages for a local dealer of electric motors. I don't really think that there should be anything special as long as the output shaft and mounting are the same. Good luck sorry I don't have better info for you.

Sep 23, 2009 | Craftsman 10" Table Saw

Not finding what you are looking for?
Craftsman 10" Table Saw Logo

Related Topics:

515 people viewed this question

Ask a Question

Usually answered in minutes!

Top Craftsman Saws Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Mike

Level 3 Expert

4340 Answers

Are you a Craftsman Saw Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...