Question about Whirlpool Cabrio WTW6600SBT Top Load Washer

1 Answer

The F1 error message keeps coming up. what do i

The F1 error message keeps coming up when i start the machine and then before the load ends. what do i need to do

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 193 Answers

Indicates a fatal error on computer board, WHIRLPOOL has had numerous problems with this issue.I would call Whirlpool to see if they will help

Posted on Nov 15, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

F1 code


F1 is a flood sensor fault code. The problem sometimes comes from loading the machine above the top of the drawer. When the inside lid comes down before the dishwasher starts, it cannot seal completely and water can spray into the outer cavity. The water accumulates in the inner bottom where there is a sensor. The sensor protects the electronic components from getting wet by warning you of the water which you cannot see. The solution is to remove the bottom drawer and wipe out, then dry the compartment with a fan or a small space heater. Once dry, the machine will function as usual.

Jan 24, 2013 | Fisher DD603FCSS Dishwasher

1 Answer

The f1 code on the Maytag Bravos top loading washer keeps going off and stopping the machine


Please contact Maytag to inquire about the code F1. They should check the system and that that code is a courtesy repair and should be scheduled for a someone to come out to fix it. FREE
It is possible that the F1 code was caused by your laundry habits (detergent), but I think that is unlikely. Too many of these machines have problems with the F1 error code. There is a known problem with the Oasis / Cabrio / Bravos machines.

Aug 19, 2010 | Maytag Bravos MTW6600T Top Load Washer

1 Answer

F1 error


yep electronis control board in the console is bad.

Apr 26, 2010 | Kenmore Elite Oasis 27052 Top Load Washer

1 Answer

I get an F1 signal when I start the washer. I can get it to go away by switching what kind of load it is but it keeps coming back?


F1 means communication error, Unplug washer for 2 mins.. What might have caused this problem is a power glitch of some kind.

Jan 17, 2010 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer

F1 error message machine stops and just beeps until you cancel and start over


F1 usually means a communication or an electrical error.

Unpgug the machine for 1 minute and then power back up. If fault reoccurrs check all connectors.

Good luck, I hope this helps

Nov 27, 2009 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer

Whirlpool washer Model WTW6600SW2. Error F1


My boss's washer has the same problem, located the tech manual inside the washer at the front it was saying to check the pressure hose for any kinks if no kinks found and problem continues replace the motor control board.

Nov 13, 2009 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer

I keep getting the "F 1" error message when i start a load, what should i do


The F1 error code on the Whirlpool cabrio is quite common, and generally has to do with the control board. Replacing the control panel may resolve this issue. However, I beleive Whirlpool is aware of the F1 issue with the Cabrio, and is fixing some machines for free. Please call 1-800-253-1301 for more details and see if you are eligible for a free repair.

Nov 03, 2009 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer

Whirlpool Cabrio Washer Error message code F1


HELLO, Error code F1 indicates a control failure and most likely the machine control board will have to be replaced. Depending on when you purchased the machine, the board may be covered under extended component warranty.
I had the same F1 problem and they had to replace the control board and something relating to the balance. The tech told me this is a common problem.

Apr 06, 2009 | Whirlpool Duet 3.8 cu. ft. Front Load...

Not finding what you are looking for?
Whirlpool Cabrio WTW6600SBT Top Load Washer Logo

280 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

yadayada
yadayada

Level 3 Expert

75005 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...