Question about Kenmore Dryers

1 Answer

Kenmore Dryer, model 86950100 PARTS

I have a Kenmore dryer, model 86950100, and i can't seem to find any information on it. Was this dryer recalled. I need to replace the lint trap for it and sears isn't even recognizing the model number.

Posted by on

  • Curtis Sewell
    Curtis Sewell May 11, 2010

    Be sure you put the (.) in your model number such as 869.50100. I see you did not do that with this one. Sears will not find the parts list without that dot. Good Luck, I hope this helps


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I was just looking for a part for mine, too. On the tag inside the front door is the pre-printed prefix 110. that goes with the 86950100 that's printed later. So, I entered 110.86950100 and found the information for my model.

My unit has been working reliably for many years now, and some parts are not available anymore. I think I bought it in about 1985. I replaced a thermal cut-off switch in 2009 for $15 locally. I also have a matching washer. I've never had any failures with it. Bear in mind that I was single for 20 of those years with only a few girlfriend-hours on them. :-)

The direct link to Sears parts for my specific model is!retrieve.pd?modelNumber=110.86950100.

Hope this helps.

Posted on Jan 22, 2010

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

11076812693 drum won't turn.

Kenmore Dryer Model 110.76812693 (11076812693) Drum ...
Kenmore Dryer Model 110.76812693 (11076812693) Drum & Tub Parts in stock. One million parts for 125 brands. Guaranteed same-day shipping. Call 7 days ...

Kenmore Dryer Model 110.76812693 (11076812693) Motor ...
Includes pulley for dryer drum drive belt. Other shaft has reverse threads for blower wheel. Common symptoms of a bad drive motor are: -Dryer stops turning ...

Kenmore, Whirlpool Dryer Repair - Heats properly, drum will ...

? 6:29
Jul 10, 2013 - Uploaded by
Service a Kenmore Dryer with some of the following issues: Heats but ... Kenmore, Whirlpool Dryer Repair - Heats properly,drum will not turn - 11068202794 ..... Whirlpool Kenmore Maytag Amana Dryer Won't Start - Easy Fix ...

How To Fix Dryer That Won't Tumble ' Dryer Repair

Feb 08, 2016 | Kenmore Dryers

1 Answer

I have a kenmore elite he3 smart heat quiet pak4 how much is a motor for this dryer

  1. Kenmore Elite He3 Parts -‎‎rating for
    Shop Today at Sears PartsDirect™. The Largest Appliance Parts Seller.
    Ratings:Shipping 9/10 - Website 9/10 - Selection 9/10 - Quality 9/10
Search Results

    MOTOR diagram for model # 41794130000 Kenmore-elite ...
    MOTOR Diagram and Parts List for KENMORE ELITE Dryer-Parts model # ... MOTORdiagram for model # 41794130000 Kenmore-elite-Parts Dryer-Parts (18).

    PUMP AND MOTOR PARTS Diagram & Parts List for Model ...
    PUMP AND MOTOR PARTS Diagram and Parts List for KENMORE ELITE ... ANDMOTOR PARTS diagram for model # 11047789702 Kenmore-elite-Parts ...

Nov 01, 2015 | Kenmore Dryers

1 Answer

Kenmore dryer recall

Any recalls on Kenmore Elite Oasis Electric dryer?
it seems many people had problems with the control board

Jan 11, 2014 | Kenmore 63102 Electric Dryer

1 Answer

Schematic kenmore 110 96585200

Firstly, take off the vent that hook up to the rear of the dryer, if the dryer got heat again. You should clean the vent. Else, there are quite a few component caused no heat. They are: thermal-cut-off (non-resettable), heating element.
Beware to unplug your dryer before opening it. The cut off thermal and heating element can check it connectivity by ohm meter. Normally, the cut-off causes this issue.
Check this link for more information

Oct 15, 2013 | Dryers

1 Answer

Kenmore dryer model 86950100, when I push the start button it just hums and will not start.First time it did it I waited 1/2 hour then it ran fine for couple days and now it started again, just hums. I...

the humming is coming from the motor,if you can spin the drum by hand and it moves freely you need to replace the motor,if it's hard to move you need to take the dryer apart to see why it's hanging up,the overload resets on the motor that's why after a while you'll hear the hum again,if you hold the button to long you'll pop the overload

Mar 26, 2010 | Kenmore Dryers

1 Answer

How do i replace the belt on a kenmore model/stock # 86950100 69501 i have the machine open and the old belt out but how does the new one go in?

hard to describe, but place belt on drum pulley, through safety switch , then motor pulley, looks like 2 loops, kind of like a car

Jul 24, 2009 | Kenmore 74742 Gas Dryer

1 Answer

Kenmore dryer will not come on

make sure your door switch is good / if not the dryer wont start / larry

Dec 05, 2008 | Kenmore 74742 Gas Dryer

Not finding what you are looking for?
Dryers Logo

Related Topics:

665 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dryers Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Sal DeAngelo

Level 3 Expert

2122 Answers

Tim Whalen

Level 3 Expert

3074 Answers

Are you a Kenmore Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides