Question about Hotpoint Aquarius WD63 Front Load Washer/Dryer

2 Answers

Not draining after cycle

Hi,

Our washer dryer is not always draining after a cycle. When it's finished there is quite often a big puddle in the bottom of the drum and the clothes are soaking wet. any ideas?

Also, the clothes are quite often more damp than when we started when wwe tumkble dry them.

Please help!

Posted by on

  • shackjon1 Aug 30, 2008

    My Hotpoint WD63 is not draining after wash, I have looked at other
    solutions but these don't seem to help. I cant find the filter referred
    to in other comments to clean it. I have tried putting the washer on
    spin but this doesn't seem to help.

  • mmcclean Sep 13, 2008

    Hi, there is a big pool of water after a wash cycle. I'm assuming it is a blockage in the filter. How do I access the filter to check? Or could it be a different problem?

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hi, there is a big pool of water after a wash cycle. I'm assuming it is a blockage in the filter. Where is the filter so that I check?

Cheers

Posted on Sep 13, 2008

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Try checking the filture on the front at the bottom of the machine they some times get full of muck

Posted on Jan 08, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi, We just moved into


On the bottom of the rubber seal, there is a drain hole. Check to see if it is clogged and clear it out if it has an obstruction.

Jan 01, 2011 | Washing Machines

1 Answer

Fisher paykel dishwasher dd601I runs complete normal cycle and finishes normally. 2-3 sec. after completion the washer motor srarts to run and the f1 fault (flood sw. activated) is dislayed. When the power...


Hi

F1 code indicates an overfill condition which may cause when dishwasher can’t pump out dirty water due to a plugged drain hose.
open dishwasher fully ,dry up as much water as possible then put a hair dryer on hot and direct into the back of the cabinet you will see a grey plastic cover on the bottom floor this is the sensor run on full for about 5 - 10 minutes making sure the heat go into that area. Also don’t overheat your hair dryer, when finished close the dishwasher shut and start your normal cycle.

Thanks for contacting fixya.com

Jan 20, 2010 | Dishwashers

1 Answer

Washer leaking from the bottom


make sure your drain pipe is not backing up when washer drains

Jan 10, 2010 | Washing Machines

1 Answer

Washer giving F2 error during wash cycle, cycle doesnt finish


HI. this code represents a Long Drain issue.

If the drain time exceeds 8 minutes, the water valves are turned off and F02 is flashed.

Press PAUSE/CANCEL twice to clear the display.

NOTE: After 4 minutes the “Sud” error will be displayed, then 4 minutes later the F02 error code will be displayed.

Potential Causes

• Check the drain hose and make sure it is not plugged or kinked
• Check the electrical connections at the pump and make sure the pump is running.
• Check the drain pump filter for foreign objects
• If the above does not correct the problem replace the pump

Oct 26, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

I have a Zanussi WDA1055W washer/dryer. I never


the water should only be filling up to approc 2in above the drum bottom...........look inside when its filling..........if its filling to nearly the bottom of the door you either have a faulty pressure switch or grit/dirt in the internal filter.......as a result the machine will not spin if there is too much weight in the drum

Feb 23, 2009 | Zanussi F1045W Front Load Washer

2 Answers

Dishwasher maytag 945 awq


Door gasket or sealOver time, door gaskets and seals harden and lose their ability to seal properly. You can't repair the seals. You need to replace them if they've begun to leak.

Nov 08, 2008 | Maytag MDBH945AWW / MDBH945AWQ /...

1 Answer

Washer/Dryer not drying


is your dryer a conderser type
does it have a tank that you have to empty at the end of cycles
if it does the filter that condensers the water from drying cycle
if that is blocked it will not work

Jan 25, 2008 | Equator EZ 3710 Front Load Washer / Dryer

1 Answer

Washer leaking water from bottom


Probably a main tub seal, big job!

Nov 16, 2007 | Maytag MAV7600 Top Load Washer

Not finding what you are looking for?
Hotpoint Aquarius WD63 Front Load Washer/Dryer Logo

248 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

vince

Level 3 Expert

1216 Answers

Eric Taylor

Level 3 Expert

560 Answers

ptpumpman

Level 3 Expert

408 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...