Question about JVC AV-27230 27" TV

1 Answer

Opening the case of a JVC Remote Control

I have an RM-C742 Remote control for my AV27750 JVC TV. This Remote sends all codes correctly except the channel up and down, the volume up and down and the power on and off. Because these were the most frequently used switches on the remote, I believe they need cleaning or burnishing, but I can't open the case of the Remote Control.

Can you tell me how to open the case of the JVC RM-C742 Remote Control?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 579 Answers

Not having seen that particular one, remote cases usually have a couple screws under the battery to lock the case together and then a number of plastic tabs around the perimiter that hold the joint closed. find the screws (sometimes they hide them under labels) - I don't know what it is about screws that manufacturers don't like to show. Either think they are not cosmetic or don't want us take-it-apart maniacs to get in. Anyway, get the screws loose then (this is the hard part) carefully pry open the case joint, feeling where and how the tabs snap out and then be careful not to have everything inside go flying when the last one lets loose. Almost impossible to not leave little gouge marks in the joint.
Hope Ya Fis It!

Posted on Jan 08, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to program JVC Remote RM-SXV067A Remote to TV


Direct Code Entry
  1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
  2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
  3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
  4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.

Jun 20, 2012 | JVC RM-A5 Remote Control

2 Answers

CODE FOR CHUNGHOP REMOTE FOR JVC TV


Hello
Setup codes for JVC TV with Chunghop RM-962 universal remote control are:
0077 / 0119 / 0178 / 0179
OK.

Jul 14, 2011 | Universal Remote Control Remote Control

1 Answer

What is the code for my hd 52786 jvc tv trying to program a dish network remote


Try these codes, the bold ones work the most often: 557, 558, 642, 559, 508, 649, 655, 667, 673, 676, 726, 735, 736, 737
If the codes don't work try the steps below:
1.) Hold down the clear "TV" button on the remote for four seconds, then press 500 pound ( #)
2.) Hold down the clear "TV" button on the remote for four seconds, press the big power button once. 3.) Press the channel up button once per second until the TV turns off then press pound (#).

Daniel Busa
DISH Network Customer Service

Feb 02, 2011 | JVC RM-C14G-1H Remote Control

2 Answers

I have remote control no. RM-C754. I can always get Ch. 34, except for last eve. When I push the Menu button, it is all in Spanish. How do I get it changed to English, and then how can I get Ch. 34?


On Menu Look for Lanuage change it to English and then Look for Auto program for channels reprogram so it will lock on channels that it can pick up

Feb 15, 2010 | JVC Televison & Video

3 Answers

TV remote RM-ED002 for main TV works fine except volume control which has no effect. Another Sony remote, RM-ED007 for second TV works fine on main TV including volume control.


I had the same problem with sony remot control RM-ED002, take remot control apart and clean inside with damp cloth and dry with kitchen towel, thats it now use it! ;-)
When i opened mine it was some kind of moisture under volume and channel buttons, cleaning and drying it helped.

Aug 24, 2009 | Televison & Video

1 Answer

I'm looking for the manual for a Mitsubishi VCR HSU447 with the remote control RM75502 so I can program my TV to it. Thanks


1.- Turn off your TV
2.- On the remote control, set the VCR/TV slide switch to TV position.
3.- While holding in SP/EP button, press the code button listed below that corresponds to the brand of your TV
4.- Press TV POWER on the remote control. Once your TV has turned on, your remote is set up to operate your brand
TV.

Brand of TV Brand Code Button
Mitsubishi 1,2,3
Fisher 0
G.E. VOLUME UP
Goldstar 2,9
Hitachi 8
JVC MUTE
Magnavox 4
NEC 2,9
Panasonic CHANNEL UP, CHANNEL DOWN
Pioneer 6
Philips 4
Proscan VOLUME UP
Quasar CHANNEL DOWN
RCA VOLUME UP
Sanyo 0
Sharp 3,5
Sony VOLUME DOWN
Toshiba 7
Zenith INPUT
I finnaly found my VCR Manual, and I'm glad to share this info with you, because I was looking for the manual all
over the web and FOUND NOTHING!. Bye!

Mar 15, 2009 | Mitsubishi Televison & Video

3 Answers

Need remote control codes for the JVC Multi Brand Remote Control Unit, LP20303-018


It took me a week to find the right instructions and codes on how to do this so I am posting it everywhere I can to help out folks with the same remote. Pay close attention to the instructions, for instance when programming the remote for TV use make sure you hold the TV button down while you enter the code and then press OK, You also have to hold the TV button down while you use the volume and channel controls or it will just change the VCR channel.
===========================================


A
Turn on TV

Turn on the TV using the Power button on the TV or its Remote.

B
Set TV brand code

A
Press and hold TV.
B
Press MBR SET.
C
Press the Number keys to enter your TV.s brand code.
D
Press OK, and release TV. The TV should turn off.


C
Operate TV

While holding down TV, press one of the following buttons:
POWER 1, TV/VCR, TV CH+/., ^(TV Muting), TV VOL+/.,
and the Number keys.

.
For some brands, you must press ENTER after having pressed the
Number keys to enter a channel number.
TV BRAND CODE TV BRAND CODE
JVC 01, 03
SONY 07
HITACHI 10
SAMSUNG 12
MAGNAVOX 02
SANYO 13
MITSUBISHI 03
SEARS 13
PANASONIC 04, 11
TOSHIBA 08
RCA 05
ZENITH 09
SHARP 06

Cable Box or DBS Receiver Brand Setting

A
Turn on cable box or DBS receiver

Turn on the cable box or DBS receiver using the Power button on
the unit or its Remote.

B
Enter brand code

A
Press and hold CABLE/DBS.
B
Press MBR SET.
C
Press the Number keys to enter your cable box.s (or DBS


receiver.s) brand code.
D
Press OK, and release CABLE/DBS.

C
Operate cable box or DBS receiver

While holding down CABLE/DBS, press one of the following
buttons: POWER 1, TV CH+/., and the Number keys.

.
For some brands, you must press ENTER after having pressed the
Number keys to enter a channel number.
.
To change the cable box.s (or DBS receiver.s) channels, press TV
CH+/–
or the Number keys. (The CH+/–
button can be used to
change the VCR.s channels only.)

CABLE BOX BRAND CODE
ARCHER 01, 05, 17
CABLETENNA 01, 17
CABLEVIEW 15, 16, 17, 21, 25
CITIZEN 15, 16, 17, 21, 25
CURTIS 02
DIAMOND 01, 17
GC BRAND 15, 16, 17, 21, 25
GEMINI 15
GENERAL INSTRUMENTS 01, 04, 06, 11, 12, 15, 28
HAMLIN 10, 18, 23
JASCO 15
JERROLD 01, 04, 06, 11, 12, 15, 28
NOVAVISION 02
OAK 07
PANASONIC 13, 14
PULSER 15, 16, 17, 21, 25
RCA 13, 14
REGAL 10, 18, 23
REMBRANDT 01, 16, 17
SAMSUNG 05, 16, 24
SCIENTIFIC ATLANTA 02
SIGMA 07
SL MARX 05, 16, 17, 24, 25
SPRUCER 13, 14
STARGATE 05, 15, 16, 17, 21, 24, 25
TELEVIEW 05, 16, 24
TOCOM 01, 04, 16
UNIKA 01, 17
UNIVERSAL 16, 17, 25
VIDEOWAY 03, 09, 22
ZENITH 03, 09, 22
DBS RECEIVER BRAND CODE
JVC (DISH Network) 51
ECHOSTAR (DISH Network) 51
SONY (DSS) 41
RCA (DSS) 40

Changing Remote Control Code

This Remote is capable of transmitting two control codes; one set
to respond to A code control signals and another set to respond to
B code control signals. This Remote control is preset to send A
code signals because your VCR is initially set to respond to A code
signals. You can easily modify your VCR and the Remote to
respond to B code signals. When using two JVC VCRs, set two
VCRs and their Remotes to different codes, so that you can
operate these VCRs separately.

A
Set remote control code for Remote

A
Press and hold A/B.
B
Press the Number key .2..
C
Press OK, and release A/B.


.
The Remote now can transmit B code control signals.
B
Check remote control code for VCR

Press and hold 4
on the VCR for more than 5 seconds while the
VCR is turned off. The code currently set appears on the display
panel.

C
Change code for VCR

Press any key on the Remote. The VCR now responds to B code
control signals.

.
To set the Remote and the VCR back to A code control signals,
repeat the same procedure as shown above except pressing the
Number key .1”
in step B
of 1
1111.
To control two VCRs with the same Remote

You can control two JVC VCRs by switching the remote control
code for the Remote between A and B (.
step A
AAAA), keeping two
VCRs to different control codes.

.
To change only the remote control code for the Remote, DO
NOT perform steps B
BBBBand C
CCCC.


Mar 19, 2008 | JVC RM-C18G-1H Remote Control

1 Answer

RM-AV2100


Either the channel up and down buttons have both broken (unlikely) or everything else is working except the remote is not telling the device you are controlling to change the channel up or down.

Since all the other buttons are working well, that also requires that the receiving end of the pair to be working well, thus ruling out problems on that end.

Solution: Reprogram your remote to support the appropriate channel up/down codes for your TV/Tuner in question.

Dec 14, 2007 | Sony RM-AV2100 LCD Touchscreen Remote...

Not finding what you are looking for?
JVC AV-27230 27" TV Logo

1,023 people viewed this question

Ask a Question

Usually answered in minutes!

Top JVC Televison & Video Experts

The Knight
The Knight

Level 3 Expert

75846 Answers

Jaime Hernandez

Level 3 Expert

2336 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a JVC Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...