Question about Pioneer PureVision PDP-502 50 in. Plasma Television

4 Answers

PDP-502MXE dead set

I have a Pioneer PDP-502MXE 50" screen which has recently stopped working. There seems to be no power getting to the set as the s/by LED doesn't light. Any advise on fault and/or cost of repair would be greatly appreciated. Thanks

Posted by on

  • 4 more comments 
  • deanos May 11, 2008

    Hello, I went to turn on my pioneer pdp 502mxe on the other day it blew the fuse in the plug, I replaced the fuse with another 5 another 5 amp fuse which it blew straight away when I tryed to turn it on again. I put a 13 amp fuse in the plug and now it sounds like it is trying to turn on but then closes down. It does this a couple of times and the green standby light goes on and off slowly.

    Any advice would be greatly apreciated

    Thanks a lot, Dean

  • Riddim36 May 22, 2008

    I have the same problem as deanos. My 10A fuse blew in set. Replaced a
    large MOSFet on a heatsing with two others. Short between source and
    gate. Now fuse is ok on power up but D407 lights after two relay clicks
    and the Stdby LED is green for 5 seconds and off for 0.5 seconds. Relay
    feeding high voltage AC to bridge rectifier is preventing this in the
    shut down state. Static checks have not revealed anything obvious so
    far on the main power supply panel. Please help if you can....

    Many Thanks.........Riddim36

  • Anonymous May 28, 2008

    had power then went to turn on later and no power

  • ptw02118 Jun 27, 2008

    The unit doesn't seem to get any power.

  • Anonymous Sep 06, 2008

    My PDP-502 failed in 2004. Pioneer service replaced the power unit but charged for the call-out (not like the US where it was FOC). I was told that replacing the fuse to test could cause additional failure within the unit and that I was lucky not to have tried.

  • Anonymous May 12, 2009

    yes i have the same problem i was watching tv as normal one night and switched it off as normal and the next morning i went to switch it on and the green lightcame on for 3 seconds and then went red again it keeps on happening. can anyone help pleaseee...

×

Ad

4 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Hi all,
this problem lis the power supply board. be aware that pioneer pdp-502mxe has got 3 versions and all 3 power supply boards are different so before ordering a new or reconditioned one check the part number on the power board itself.
pioneer is not replacing the boards anymore.
check on ebay.co.uk
i did sold so many parts from this model.
thanks

Posted on Sep 05, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

This same thing just happened to me. I read that it might be a power supply failure which Pioneer will fix.
http://www.pioneerelectronics.com/PUSA/Support/ci.Important:+Updated+Information+Regarding+Free+Power+Supply+Replacement+for+Certain+Pioneer+Plasmas.Print?format=Print

Waiting for them to open during regular business hours. Hope this helps!

Posted on Jul 20, 2008

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Do you want to sell it, Email elizabethbell_10@hotmail.co.uk

Posted on Jan 09, 2008

  • alexbell_10 Jan 09, 2008

    Any one with dead pioneer pdp sets for sale email me.

  • generalusedi Sep 13, 2011

    I have dead pdp 42inches . .who wants to buy this . . . .this tv is clean ..looks great but can not power on anymore

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,153 Answers

Fuse in power supply, would need schematic

Posted on Jan 08, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sound isn't working on my pioneer 5071 pdp


Does the set have sound with a DVD etc. directly connected to one of the audio/video inputs this set has?

Apr 30, 2012 | Pioneer PDP-5071HD 50 in. Plasma HDTV

1 Answer

I have a pioneer pdp-502mxe, display screen i am watch my cable tv on it but the picture is fuzzy, would i benifit forn upgrading my virgin box to hd one or would a media reciver solve the problem


upgrading to an HD receiver would very much clear up the picture on flat panel

you are watching a standard definition signal expanded to fit the screen - it is like trying to paint the whole house with one rooms worth of paint

Mar 27, 2011 | Televison & Video

1 Answer

My pioneer pdp 5030hd display stopped working and the green LED flashes continuously! Help!


The tv power supply board is the problems and the causes,it dead.That the board,where the power a/c cord plug into it.Try website like Ebay.com to buy whole refurbish power supply board for the replacement.

Dec 12, 2010 | Pioneer PureVision PDP-5030HD 50 in....

1 Answer

I heard a pop from my tv and then the tv didn't work


Anything is repairable as long as the screen isn't damaged.
The sound you heard is most likely was a capacitor that just went dead.
Solder in a new capacitor should fix the problem. It would most likely be on the power supply board somewhere.

You'll need the Service Manual for parts list, diagrams, and schematics. Here's one place for that:
http://www.manuals-in-pdf.com/advanced_search_result.php?keywords=pdp-503cmx+service+manual&forward=plist

Any other questions just ask.

May 10, 2009 | Pioneer PureVision PDP-503CMX 50 in....

3 Answers

Green spots/pixels at top of TV screen


I have a 50" Pioneer PDP-503MXE with the same problem - the fans don't run. It appears to be a problem with the temperature sensor that controls the fan speed. However, the fans can manually be switched to MAX.
To do this, put the display in standby. Press the 'Menu' button and within 3 seconds press the 'Power/Standby' button. The 'Integration Menu' will appear. Select the 'Option' tab on the right. Scroll down (next page) to the 'Fan Control' option. It will most likely be set to 'Auto'. Press 'Set' to change it to 'Max'. Within a few seconds the fans will run.
At Max the fans are a bit noisey but it will cool the unit down.

May 05, 2009 | Pioneer PureVision PDP-503CMX 50 in....

1 Answer

Screen Picture is Cut off


did you try pushing the input key on your remote it might change the screen if that don't work then try to go in to the settings in the remote

Nov 09, 2008 | Pioneer PDP-5060HD 50 in. Plasma...

2 Answers

Pioneer pdp 503


Hi, my PDP 50XE just cut out, when powered back on the screen powers down and the standby light flashes twice followed by a 5 sec gap.  Anyone got any thoughts? Thanks

Jun 28, 2008 | Pioneer PureVision PDP-5030HD 50 in....

2 Answers

My PIONEER PDP-503HDE 50 INCH PLASMA screen won't power up


you guessed right you got a problem with the projector, I always point my finger to Power suppy problems on these sets for about any other problem would mean throw-away or too expensize to fix. good luck

Sep 01, 2007 | Pioneer PureVision PDP-503HDE 50 in....

Not finding what you are looking for?
Pioneer PureVision PDP-502 50 in. Plasma Television Logo

Related Topics:

1,480 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pioneer Televison & Video Experts

The Knight
The Knight

Level 3 Expert

75462 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Jaime Hernandez

Level 3 Expert

2336 Answers

Are you a Pioneer Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...