Question about Standard (CRT) Televisions

1 Answer

Sanyo TV How to connect a sanyo tv, with a DVD and VCR. I have one video.. any know how to hook it up.. Where does the video out goo too. thank I have a sanyo tv model number ds27510. just had to get a new remote. i programed the remote. i have an rca dvd player/ rca remote. i have it hooked up correctly...but on the tv menu...there is no place to switch to the movie, and it appears on no channel. . when i push the input tv/vcr/dvd button, all that comes up is the channel 2 appears on the screen. on the tv menu, there is nothing about video input, etc. our old remote worked with no problems on this tv and dvd.

Posted by on

1 Answer

Re: Sanyo TV

I too just bought an RCA remote for the same television. The button to access other video screens is the A/B button on mine (next to the last channel button).

Posted on Jan 11, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Sanyo TV connect to cable box connect DVD player

If your DVD/VCR combo player has three RCA connectors (yellow, red, and white), you can connect them to the corresponding inputs on the front of your TV.

Dec 29, 2012 | Sanyo Standard (CRT) Televisions

1 Answer

Have inherited this tv, no manual. Have to use Directv remote. Am trying now to connect new Toshiba vcr/dvr recorder, but TV go on menu to any "input" channel. Does this tv not have an...

Check the tv manual buttons,have a input button.No.Try website like to buy an original remote so can find out with input ur VCR/DVD device unit hook up into like video input like 1 or 2.

Jan 17, 2011 | Sanyo DS27800 27" TV

1 Answer

I do not have the original remote to the sanyo DS27510 27" tv. But there is no option on the tv menu button to program a video 1 or video 2 channel. Do you know a way how to program somewhat like an aux...

IF your tv doesnt have the VIDEO & AUDIO IN , then you need to purchase an RF adaptor to connect a DVD OR VCR , usually sold at RADIO SHACK , HOPE THIS HELPS AJ

Nov 09, 2009 | Sanyo DS27510 27" TV

1 Answer

No audio when using VCR/DVD player

the first thing that you need to do is use the video cables and audio cables that are on the back of the unit. This makes sure that you have sound and video.

Dec 22, 2008 | Sanyo DS27510 27" TV

1 Answer

Dvd/tv hook up

plug in dvd player direct to tv yello red white for sound into a input ok vidieo one ect then change input on tv to that input ch2 hit ch down to go into inputs

Feb 10, 2008 | Sanyo DS31590 31" TV

3 Answers

Sanyo DS25830 and DVD player...

did you ever fix the problem if so I would like to know how cause it don't look like anyone has helped you and I would like to know if the dvd can be hooked up to this tv?

Nov 21, 2007 | Sanyo DS25390 TV

1 Answer

Sanyo TV


If I understand your posting/description right, you have:
1, a Sanyo TV with only 1 video input;
2. you have a DVD player with only video output; and
3. you have a VCR (which I will assume to be with both video input and output).

Your query, if I may clarify, is how to hook them up so that you need not connect/disconnect any video cable when you want to switch video source from either DVD or VCR.

If that is what you want, then connect:
a. audio/video OUT of your DVD to audio/video IN of the VCR;
b. audio/video OUT of your VCR to audio/video IN of the TV.

The above described connection would allow you to:
i. watch DVD movies on your TV (your VCR must be powered ON and set to Video INput, your TV must be powered ON & set to Video INput);
ii. watch tape movies from your VCR without disconnecting/connecting cables.

Additionally, this arrangement would allow you to record DVD movies in your VCR. Further, connecting your cable/aerial to the RF INput of your VCR would allow you to do the same with a TV/Cable program.

Incidentally, if one of your units (TV, VCR, DVD) would only have a single audio input, it is still possible since some models uses the white audio RCA connector as either left or mono, the red is right. You can also use a 2 female RCA to 1 RCA male adapter as shown below to joint the red/white audio.


Hope this be of some idea/help. Pls post back how things turned out or should you require additional information.

Good luck and kind regards.

Nov 19, 2007 | Sanyo DS32224 TV

1 Answer

TV (Model DS27510) is stuck on Video2 setting, unable to change!!

Ours is doing the same thing except on Video 1. I called Sanyo customer service and they said I need the original remote. They were willing to sell me one for $20. Here is what I did instead. I used a cable box and hooked the cable in to it. Then I took the type of cables that will hook into my video 1 slot and plugged them in there and plugged them into the back of the cable box in the "cable out" positions. It worked ! If you do not have a cable box you might try a DVD/VCR combo or a VCR. Good Luck

Sep 16, 2007 | Sanyo DS27510 27" TV

1 Answer

Hooking tv up to my vcr/dvd combo

hook the antenna to the VCR rf conecter IN. buy some RCA jacks and a three way deal and hook the red to sound red out ,white to sound output white, and yellow is always video hookit to yellow vido out on the vcr/dvd. The other ends go to the inputs on the TV....same color code. or you can just hook a cable to rf connector OUT on the vcr and other end to( it with problably just same antenna in) to TV.

Aug 29, 2007 | Sanyo DS31520 31" TV

1 Answer

Connecting VCR/DVD combo

Put the Tv on Channel 3

Jul 11, 2007 | Sanyo DS25390 TV

Not finding what you are looking for?
Standard (CRT) Televisions Logo

Related Topics:

389 people viewed this question

Ask a Question

Usually answered in minutes!

Top Standard (CRT) Televisions Experts

The Knight
The Knight

Level 3 Expert

66409 Answers

matt martin
matt martin

Level 3 Expert

1187 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Standard (CRT) Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides