Question about Computers & Internet

1 Answer

Wyse Terminal I have an old Wyse (WY 60) terminal installed as an elevator control monitor. This unit was recently replaced with a rebuild (by elevator contractor) and everything seems to work however, I cannot get reports to print. Info can be viewed on screen so it is being collected. I suspect problem is in user configuration settings but don't know enough to determine what to change.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 859 Answers

Do you have a print screen button, sometimes abbreviated PrtScr on the keytops. I would get the contractor back on site and have them setup the machine so you can print, they left the job unfinished and I would emphasize that when you call back.

Posted on May 11, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is't opossible to get complete schematic for an


http://fileshare.eshop.bg/
is the only place I can think of

Jan 15, 2010 | WYSE WY-370 (wy370)

1 Answer

Only one line


Hold the G key down on power up and leave the G key pushed in till you get a screen, then go to set up and defult all, then re set up the unit.

Jul 04, 2009 | WYSE NEW WY-60 AMBER 80 (90010907) Network...

1 Answer

Wyse 1200LE - error - out of frequency


This is caused by the terminals default display resolution (or the resolution that it was set to in its previous environment). The easiest way to get a display, would be to use a different monitor with a higher range of supported resolutions.

Fingers crossed the previous wnos.ini file would allow a G-key reset. If so, just hold down the G key when the terminal is booting, and it will reset to factory defaults. This might allow your monitor to work. (I think the default resolution is 800x600)

The problem you have is that the terminal might be locked down via the .ini file. So changing the configuration might be difficult. You could use a program like Wireshark to perform a network trace, this would tell you where the terminal is looking for it its wnos.ini file.

Then you will be able to setup a new wnos.ini on an FTP server set to the IP address(and path) the terminal is looking for, and this will allow you to set your own configuration.




May 28, 2009 | WYSE Winterm S30 Network Terminal

2 Answers

Saving things in the WYSE WY-150


Hello,

As far as i know the monitor can do very little and internal storage capacity is not big at all.

Rory Cardenas
Midrange Repair and Parts
Alsip IL 60803
708-597-4222 e 240
rcardenas@mrp.to

May 08, 2009 | WYSE WY-150 Network Terminal

1 Answer

The wyse 50 terminal does not work properly


Hello,

Wyse 50/60/150/160 monitors were my specialty!

From what you were explaining it seems to me that you have a bad internal battery and it needs to be changed and a factory reset/ calibration needs to be performed.

I can repair wyse terminals at my facility if you like. The repair cost is not that high and we can also perform the regular repair and adjustments on all wyse monitors if needed.

Please contact me if you have any questions.

Thanks

Rory Cardenas
Midrange Repair and Parts
Alsip IL 60803
708-597-4222 x240
rcardenas@mrp.to
AOL IM: RORYMRP

Mar 18, 2009 | WYSE 50 Terminal

1 Answer

How to connect wyse wy-185 to at&t 577 printer


Dear mm6529, I have an At&t 577 printer, but do not have a manual for it. Any ideas where to get one or could make a copy for me.
blevinsb33@aol.com

Dec 03, 2008 | WYSE 900986-07 185 Terminal Amber w/o...

1 Answer

Wyse 1200LE - error - out of frequency


The display settings are not valid with the monitor. Either you are using a new monitor or you have changed the settings. If you are using a new monitor, swap with the old monitor and configure the appropriate refresh rate for the new monitor.

If you have changed the settings you may need to either reset all default settings, or setup a parallel unit and use the same key strokes to change the display settings on the problem unit.

Cheers..

Apr 02, 2008 | WYSE Winterm S30 Network Terminal

1 Answer

No display in monitor


This may be the problem with the WYSE driver. Ensure that correct driver is intalled and colour profile is compitable. Syncmaster is auto detected by window based OS.the message "Sync out of range" comes due to improper out put video signal.

Jul 24, 2007 | WYSE Winterm 3235LE Network Terminal

1 Answer

Display problems


There is a hotfix you can download from the WYSE Website but you have to setup a FTP server to get it installed. An easier way that seemed to work for us so far is go into Control Panel -> System -> Memory Tab. Adjust the memory slider so about 1/4 of the memory is set aside for Storage Memory (The systems I changed had between 90-100% set aside for Program Memory leaving 0-10% for Storage Memory.

Feb 23, 2007 | WYSE Winterm S30 Network Terminal

1 Answer

Blue Screen of Death


If it narrows it down for you, Trident 3D is the graphics display your motherboard uses, and must have a driver issue or conflict with your monitors drivers, check in device manager for your monitor type to see if it's recognised.

Nov 02, 2006 | WYSE WT941GXL Xpe 192/256 (902073-05)...

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

595 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18425 Answers

Alun Cox

Level 3 Expert

2678 Answers

David Payne
David Payne

Level 3 Expert

14162 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...