Question about ASK Proxima M1 Multimedia Projector

1 Answer

Loses source signal to the PC after heating up.

We have a Ask Proxima M1 projector that initally works fine but after a few minutes it loses the source signal to the computer and starts searching for a source. After searching it connects again, flashes the display from the PC and then starts searching again. I have cleaned the vents and it continues to have the problem. Any ideas?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 74 Answers

I would first make sure the cable is not having an problems. But when I worked at a repair shop the main board was always the problem when giving these symptoms.

Posted on Nov 13, 2009

Testimonial: "Thanks for the confirmation. I had tried a couple of different cables to no success. Suspected the board but thought I would check Thanks."

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Finding Source problem in pj458d viewsonic projector


interface of inputs is defective
Have a good day!
We supply original projector parts: lamp, bulb, Lcd panel, Lens, DMD chip,color wheel, motherboard, powersupply ... with high quality and competitive price.
Jerry China Lampdeng Limited
Tel: +86 131788 67858
E-mail: lampdeng@hotmail.com
Skype: lampdeng.com
YM: lampdeng@yahoo.com
http://facebook.com/lampdeng
http://www.lampdeng.com

Feb 17, 2014 | ASK Proxima M1 Multimedia Projector

1 Answer

When i connect the projector to my computer, all it says is no input selected. i need help with this IMMEDIATELY!!!


make sure the computer has the output screen signal enabled on the external rgb connector. you can confirm this by connecting an external lcd monitor to the pc. swap the pc vga output to the projector.
then make sure the vga/rgb input source is selected on the projector.
also select the lowest resolution on the pc to start with. when a picture appears on the projector, then increase the pc screen resolution until it says it's not able to show it, and back off to the last setting that worked

Apr 13, 2011 | ASK Proxima Office Equipment & Supplies

1 Answer

In Focus Ask Proxima M2+ has a squeaking noise and the image flickers. After about 30 minutes the unit goes to standby.


Bearing on the fan is probably shot, causing the unit to heat up and shut down. Repair would more than likely exceed the replacement value of the projector.

Mar 14, 2011 | InFocus ASK Proxima M2+ Multimedia...

1 Answer

I have a proxima 6850 and at least once a week it shuts down like the lamp has gone out, I turn it off for a minute from the power switch on the side of the projector and when I turn it back on it works...


Sounds like a heat issue, direct a small table fan into the unit next time and see if it stays on longer. If so then you may want to blow out the case with compressed air to get dust accumulation off heat sink or internal radiator.

Oct 19, 2010 | ASK Proxima PROXIMA DP6850 projector lamp...

1 Answer

How to connect my C160 ask proxima to my laptop hp?


C160 has M1-DA connector. You need an adapter.
Try this or Google it.

Dec 06, 2009 | ASK Proxima C160 Multimedia Projector

1 Answer

Blue Screen


you have a dmd chip failure or a main board failure. may just need reflashing.

Jan 21, 2009 | ASK Proxima M1 Multimedia Projector

1 Answer

Proxima c420


yes. the lamp is starting to go.

Aug 19, 2008 | ASK Proxima C420 Multimedia Projector

1 Answer

Proxima Ultralight x350 no valid input source error?


reset the settings to factory default. if that doesn't work, the lamp may not have enough power to stay on. if the lamp doesn't have many hours on it, it's the ballast.

Jan 05, 2008 | InFocus Proxima UltraLight SP1 Multimedia...

Not finding what you are looking for?
ASK Proxima M1 Multimedia Projector Logo

212 people viewed this question

Ask a Question

Usually answered in minutes!

Top ASK Proxima Office Equipment & Supplies Experts

jasbo
jasbo

Level 3 Expert

2237 Answers

240cpa

Level 3 Expert

548 Answers

Lyle Siemens
Lyle Siemens

Level 2 Expert

328 Answers

Are you an ASK Proxima Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...