Question about Gemmy 4 Ft. x 6 Ft. Airblown Thomas the Train

5 Answers

I can't get my gemmy amazing light and sound show christmas tree trio to work on a timer. Does anyone know how to bypass the remote control?

Posted by on

5 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Did you figure it out b/c I lost my remote and trying to figure out how to bypass the remote as well.

Posted on Nov 30, 2009

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

There is a star button in the controler box that you put on

Posted on Dec 16, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

I used a stereo plug extension wire like you use to extend headphones. You plug it in to the "demo" socket dangling from the controller box on the tree. you can play with the insertion to make it light up. Once set, the light show will start every time you apply power. Play with how far you insert the headphone plug. On one position it will play one song with lights then turn off. But the light show setting plays every time power is applied but no music with this setting. It is same as Effects setting on the remote.

Posted on Dec 15, 2016

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 1 Answer

Anyone know how to get MP3 player and lights to work at same time on the trees? I can get music to play but no lights

Posted on Dec 06, 2014

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 11 Answers

I don't believe it can. I have mine on one of the timer circuits but once power is applied the unit just sits until you either activate it from the remote or use the 'demo' switch. If you know someone with electronics knowledge, they can probably work up a small circuit with a relay that will momentarily close a few seconds after power is applied. Use this relay closure to activate the unit via the demo switch.

Posted on Jun 03, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

I have the Trio Outdoor Lightshow Tree from Gemmy. It worked great until we had to replace the batteries in the remote. I have tried to reset both the box and the remote, but no luck.


push the reset botton on the box in the tree, on the back if the remote there is a reset bottom, push the reset botton on the tree until the light start to blick then push the reset botton on the remote, thats what i did to mine

Dec 02, 2009 | Gemmy Inflatable Polar Bear on Motorcycle

3 Answers

MY 3 PIECE GEMMY CHRISTMAS TREES STOPPED WORKING THE SPEAKER FOR MUSIC JUST KINDA HUMMS AND THE LIGHTS WILL NOT WORK


Here's what you do... This is for the trio christmas tree light show.
What you need.... small precision pointing tool.
On the largest tree base electrical box there is a push button. Press and release that button. A red led will flash indicating the box is in sync mode. turn the remote on and on the back of your remort, there is a small hole with the words reset over the top of it. Using the small precision pointing tool, press the recessed button and release. The remote will sync to the base unit. Walla!! Merry Christmas to all!!!

Nov 29, 2009 | Gemmy Toys

9 Answers

We bought the Gemmy Christmas tree trio last year. Just set it up today and the light show effects will not reset. Can't find the instruction manual


Press reset on the top of the main unit under the middle tree. The light will blink. While it's blinking, use a pin to press in the reset button on the back of the remote. The blinking light should go out, and you should be good to go. FWIW - I just looked for almost an hour before I found this answer today on-line. It worked for us.

Nov 27, 2009 | Gemmy Toys

2 Answers

Gemmy trio light show tree - plugged it in and one bulb flashed bright. Doesn't work at all now. Not sure what to do?


i bough mine used it came with a remote. after you plug it in you have to push the reset button on the big box untill the led on top flashes then push the rest button on the back of the remote(with batteries already installed of course). The led on the box will stop. then turn remote to on and push a button. that should do it, I hope.

Dec 13, 2008 | Toys

3 Answers

Gemmy light show lollipops not working right


The gemmy light shows are amazing when working correctly. BUT that may be for one season only. I bought the white trio set of Christmas trees after one season the trees turned brown, tried to get in touch gemmy. Two days later my reply was I improperly stored my trees. All the other set of trees I've seen turn brown after one season. As far as I know gemmy quit making the white trees. Long story short they did't warranty my trees, as for the lollipops 4 or 5 light systems aren't interchangeable, I tried to replace the led in my 5 light system with a led from a 4 light system the led worked but wouldn't sync. When trying to make repairs you must use parts from alike sets of the same year models, alike models from different years don't work. Also when changing led circuit boards solder the wires the way you take them off or you'll short the board out. If you have bad sets of lights you can make repairs if they are alike.

Nov 18, 2008 | Sport & Outdoor - Others

Not finding what you are looking for?
Gemmy 4 Ft. x 6 Ft. Airblown Thomas the Train Logo

1,535 people viewed this question

Ask a Question

Usually answered in minutes!

Top Gemmy Toys Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

14581 Answers

Are you a Gemmy Toy Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...