Question about Hobart 41 in. AM14-255 Free-standing Dishwasher

1 Answer

Is it possible to extend the rinse cycle on a hobart am14 dishwasher it only rinses for about 10 sec.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 110 Answers

No the rinse time is non-adjustable it is built into the main control board

Posted on Jan 16, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

AM14 Display will stay in Rinse Cycle


see this probably causes:
Water-heating cycle
the heating will be importante, test the hot water, and heating elements
Timer
test the timer for contact, and probably defective.see the diagram attached.



5_8_2012_12_07_22_am.gif5_8_2012_12_07_58_am.gif

May 07, 2012 | Hobart AM14-253 Free-standing Dishwasher

1 Answer

Commmercial dishwasher has proper pressure when


same pump does both, are you certain there is nothing in front of the pump? I would pull the safety hood off and look inside

Jun 29, 2010 | Hobart AM14-253 Free-standing Dishwasher

1 Answer

Hobart dishwasher Am14, rinse cycle is too short. Can it be adjusted?


no rinse time can't be adjust on the am-14 modelit is built in main board non variable

Dec 01, 2009 | Hobart SR24C-4 Dishwasher

1 Answer

Hobart am 14 constant power on rps 1+2, rinse conection has power even when machine is in wash cycle


DPS1 and 2 are fed from L1 and L2 directly.
RPS1 and 2 get their signal from a relay, triggered during fill or rinse. Check inside the control box for the machine schematic and component location. Check that the relay only powers during fill and rinse. Check for welded relay contacts.
Note. Soap and rinse dispenses are often spliced into AM14's in unusual ways, and with unprotected pump circuits. (no fuses) These can be too much current draw for the contact rating of the relay.

Jul 02, 2009 | Hobart AM14-253 Free-standing Dishwasher

1 Answer

No water pressure in rinse cycle


AM 14's need 20 PSI flow rate of rinse. Is your pressure gauge accurate? Could the rinse nozzles be blocked with scale? If you remove them to clean, make sure they go back in the same positions. Note the upper arm has one each side pointing up, to clean the top of the machine. Check that the upper rinse arm has it's thrust washer under it's hub.

May 05, 2009 | Hobart AM14-253 Free-standing Dishwasher

1 Answer

AM-14 rinse cycle water useage


The psi should be in the green on the gauge,20-25.The 10 second rinse cycle is the default setting.

Feb 17, 2009 | Hobart AM14-253 Free-standing Dishwasher

1 Answer

Rinse PSI


I would check the line strainer to see if its clogged,I would also check the booster or filter system if installed.Let me know.

Oct 30, 2008 | Hobart 41 in. AM14-255 Free-standing...

1 Answer

No water going in to dishwasher when rinsing


the pump shouldn't turn on when the rinse cycle is on - it uses only fresh water straight from the water line - after the wash cycle is over - wait 5 seconds, then open the doors and see if there is any rinse coming out of the rinse arms.
If only a little is coming out - check the rinse arm spray jets to see if there is debris caught in them -
if no water is coming out - it could be a faulty rinse solenoid

Aug 05, 2008 | Hobart AM14-253 Free-standing Dishwasher

Not finding what you are looking for?
Hobart 41 in. AM14-255 Free-standing Dishwasher Logo

Related Topics:

241 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hobart Dishwashers Experts

Jason

Level 2 Expert

211 Answers

yadayada
yadayada

Level 3 Expert

76132 Answers

Garth Jackson

Level 2 Expert

93 Answers

Are you a Hobart Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...