Question about Maytag Atlantis MAV6000 Top Load Washer

2 Answers

How do I gat the panel off to get to the motor?

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

For pictures and step by step instructions, look here... www.applianceaid.com/atlantis.html

Hope this is what you need!
Bondo

Posted on Nov 12, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 612 Answers

Take a putty knife or flat blade screw driver. Look at the top of the front panel. Between the top and front. There is a clip under toward each corner. Slide the blade between the top and front and slid it toward the side. You will hit a clip. Now pull the blade out and push it back in so you can push on the clip. Pull the front toward you while pushing on the clip. Do this on both sides. Once the top pulls out, lift it off the clips on the bottom. Now you can get to the motor. Good luck.

Posted on Nov 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tredmill motor


contact the maker for parts or distributor or authorised repairer for parts

May 15, 2013 | Exercise & Fitness

1 Answer

Craftsman planner will not get up to speed


Is this a motor problem??? I would suspect the start/run capacitor.

Dec 20, 2012 | Garden

1 Answer

I need to know how to connect the hoses from the gas tank to the motor


your fuel line coming from the tank should be connected to the fuel pump. from the fuel pump it goes to the carb...that if youve gat a gas engine

Jul 19, 2011 | Volkswagen Cabriolet Cars & Trucks

1 Answer

Does the heater relay control the blower as well and if so where is it located


no if you blower motor does not work most likely variable fan speed resistor required tough to gat at rf feet area above your toes

Dec 05, 2010 | 1993 Pontiac Sunbird

1 Answer

Washer only buzzs


HI Randy, It sounds like the motor might be hung up. THe moter has apump on one side of it and soometimes they get plugged and will not let the motor run. Does the buz come from the back or from bottom? If it is from the back, it might be water inlet valve. Do you gat water?
please let me know so I can assist you further.

THankx
Vic

May 17, 2009 | Washing Machines

1 Answer

There is a rattle in the motor. When idleing there is an internal rattle.


take off your clutch cover and make sure your clucth basket and plates are not worn....does the noise gat better or worse with the clutch lever pulled in?

Apr 26, 2009 | 2002 Yamaha YZ 426 F

1 Answer

No volume


Sounds like if you are not getting sound then you are missing 9v to IA01 on signal board and you have an open LA01 so you will need to replace LA01. for more info ctechnicians.com

Dec 20, 2007 | Hitachi 50V500 50 in. HD-Ready LCD...

1 Answer

Dacor convection oven cps127/130 failure code f1


i found my circuit/schematic tucked inside the back panel in a envelope, you have to remove the oven from the wall to gat to it and start un screwing the panels, i think it was on the top.

Sep 04, 2007 | Ovens

Not finding what you are looking for?
Maytag Atlantis MAV6000 Top Load Washer Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

587 Answers

John Tripp
John Tripp

Level 3 Expert

4654 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...