Question about Northern Tool 10,600 BTU Radiant Kerosene Heater

1 Answer

Dyna glo RMC95C6 kero heater

Bought this unit last year new at end of season. hasnt worked right since i bought it . really hard to light . when it does light only part of wick lights. and smokes like hell. thouhgt maybe old kero but cleaned it out and put in fresh .no better .what am i doing wrong

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
Re: dyna glo RMC95C6 kero heater

I suggest you replace the wick and clean the wick feeder assembly. I did not own that model but did have one a number of years ago. The wicks can begin to dry out.

Posted on Jan 08, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

2 Answers

I just replaced the wick, cleaned up the heater and filled with new K-1 kero. The heater (Dyna-Glo RMC-95-C7) is emitting black smoke worst than ever. The wick is burning a little unevenly.

Either the wick was improperly installed or you may not have allowed enough time for the wick to soak in the kerosene and become evenly distributed. Check the placement of the new wick and allow time (several hours) for the wick to absorb the kerosene.

Jan 31, 2011 | Dyna-Glo RMC-8001SS Heater

2 Answers

Hi i have a dyno glo pro heater model number RMC-KFA170TDGP it worked great last year this year its been nothing but a pain flames shoot out the front by times sounds like its getting to much air but the...

did you try cleaning the lens of the photocell, they git dirty from smoke ver time which regulates the flame or replace the nozzle, sounds like it could be getting plugged up? usually any heating store would have a nozzle for a couple bucks if you get the number off it. the nozzle is right where it comes out and they are common to plug up at times with wear

Jan 18, 2011 | All-Pro Kerosene Garage Shop Heaters - All...

1 Answer

Have a Dyna Glo RMC-95-C2 and I can't get it to lite.

You have to change the batteries.. the manufacturer shipped it with **** batteries.

also take it apart.. very simple and clean out any soot..

Soot will cause heavy smoking...

The wick should last more than a year ....

Dec 14, 2009 | Dyna-Glo RMC-8001SS Heater

1 Answer

Have Dyna-Glo Unvented Gas-Fired Room Heater,

I had the same issue. Iwent to the local harware store and bought heay duty mirror hangers. They work great for only a few bucks.

Oct 22, 2009 | Dyna-Glo Heaters

1 Answer

Hard wick

runnig the heater too low on kerosene causes the wick to dry out an char and make sure the wick adjustment is working properly and lowering it enough to get saturated

Jan 03, 2009 | Corona 23-DK Compact Heater

4 Answers

Filters for dyna-glo pro

You can make your own filters out of felt and I have also found that with some minor modifications most of the parts from Mr. Heater will work with Dyna Glo. I have a 170btu kerosene heater and just installed an ignition, a high limit control and a flame sensor from Mr. Heater and it works like new.

Nov 03, 2008 | Desa International ALL-PRO® SPC-85 Utility...

1 Answer


well, somebody once told me that if you add a quart of oil to 5 gal of kero, it makes a good diesel substitute. So, in theory, I would add a little ethinal (corn gas) to the kero.

Feb 20, 2008 | Corona 23-DK Compact Heater

3 Answers

Dyna-Glo RMC95C6 Kerosene Heater

I have uploaded the manual for all to use here.

Feb 17, 2008 | Heaters

Not finding what you are looking for?
Northern Tool 10,600 BTU Radiant Kerosene Heater Logo

664 people viewed this question

Ask a Question

Usually answered in minutes!

Top Northern Tool Heaters Experts


Level 3 Expert

1751 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers


Level 3 Expert

1033 Answers

Are you a Northern Tool Heater Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides