Question about Garden

2 Answers

Hydraulic lift pump not lifting how to replace pump on a L245 kubota trctor

Posted by on

  • Anonymous Mar 17, 2014

    lift arms are slow lifting

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I have a Ford 1700 and the first time this happened I assumed it needed the oil changed (DID NOT read the manual). After changing the hydraulic oil for about $50... it ran no better. Read the manual. Bought the hidden oil filter. Bought new oil. Problem solved. The filter on this tractor sits in the bottom of the rear end housing and collect ever piece of junk. Good! But a pain to change the filter.

Posted on Nov 24, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 169 Answers

9 times out of 10 its not the pump. Inspect all fittings and check for leaks. Rem this rule that if oil can get out air can get in. Air is most likely your issue. Cavitation will make it act like a bad pump. Hope this helps

Posted on Nov 20, 2009

Testimonial: "thanKs very much for your prompT attention however there are NO oil leaks I AM GOING TO DO A OIL CHANGE AND CLEAN THE FILTER REGARDS DEREK "

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Repairman can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Repairman (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I own a 1996 Kubota 7040 and my problem is when I'm at idle the bucket won't lift or the 3 point hitch I have to Rev engine to get a response.All oil and filters are new also the hydraulic pump


Try turning in 1 turn C/W on the pump relief valve adjustment. It should be an Allen stud with a jam nut on the right side of the transaxle just above the axel housing. Foamy or milky hydraulic oil is an indication of leakage or blockage in suction tube for the pump.

Mar 20, 2017 | Cars & Trucks

1 Answer

1640A Kubota tractor front end loader or bush hog will not lift


I would say you have air in the hydraulic system or you are low on Hydraulic fluid, I am not sure of the procedure on this make to bleed the air out but a dealer may help you if you ask nice.

Sep 22, 2016 | Cars & Trucks

1 Answer

Kubota L2250 DT wiring diagram


You can download:Kubota Tractor L2250, L2550,L2850,L3250 2WD 4WD Operator Manual
This Manual Covers

1. Servicing of Tractor
2. Specifications
3. Operating New Front Mower
4. Instrument Panel and Controls
5. Lift Link and Hydraulic Control
6. Wheels, Tires and Tread
7. Operating
8. Maintenance
9.Check and Maintenance
10. Adjustments
11. Troubleshooting
12. Long-Term Storage
13. Lubricant Specifications
14.Wiring Diagram

Jul 03, 2012 | Motorcycles

1 Answer

To remove 1993 mustang conv. top cylinders should top be up or down? thanks, bill


don't have 93. here's 94

Motor Assembly, Convertible Top Removal and Installation
NOTE: The folding top hydraulic cylinder rods should be in the fully retracted position.
Use absorbent rags or a container to catch any hydraulic fluid that leaks out when removing the fittings.
  1. Remove motor and pump assembly as outlined.
  1. Loosen each folding top motor upper and lower hose fitting on the sides of the folding top hydraulic lift motor and plate kit (533A00) .
  1. Remove the folding top hydraulic lift motor and plate kit .
  1. Remove each of the service folding top hydraulic lift motor and plate kit plugs one at a time and attach the tee fitting to the replacement folding top hydraulic lift motor and plate kit . NOTE: Make sure that the o-ring is installed in the bottom of each folding top hydraulic lift motor and plate kit port before attaching the hose tee fitting.
  1. Connect the folding top hydraulic lift motor and plate kit unit to a 12-volt power source and cycle the folding top hydraulic lift motor and plate kit in and out several times to purge the air from the folding top motor upper and lower hoses (53390) . Some noise squeal may be noticed due to the air. srb~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not overfill or the reservoir seal could be blown out.
  1. Carefully remove the rubber fill plug from the back and the reservoir and check the fluid level. The level should be at the bottom of the filler hole. If necessary, add Synthetic Mercon® Multi-Purpose Automatic transmission fluid E6AZ-19582-B (ESR-M2C163-A2) or equivalent.
  1. Replace the fill plug with a new fill plug.
  1. To install, reverse Removal procedure.
-------------------------------------------------------------------------------------------------------------------------------
Section 01-17: Convertible 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Lift Cylinder, Power Top Removal and Installation
NOTE: The cylinder rods should be in the fully-retracted position.
  1. Remove pump and motor as outlined.
  1. Remove the upper and lower hose fitting from the folding top hydraulic cylinder (50600) . Use absorbent rags or a container to catch any hydraulic fluid that leaks out when removing the fittings.
  1. Remove each of the service cylinder plugs one at a time and attach the hose fittings. NOTE: Be sure each fitting is installed in the correct position on the folding top hydraulic cylinder .
    NOTE: Make sure that the tetra seal is installed in the bottom of each of the folding top hydraulic cylinder ports before attaching the upper and lower hose fittings.
  1. Connect the folding top hydraulic lift motor and plate kit (533A00) to a 12-volt power source and cycle the folding top hydraulic lift motor and plate kit in and out several times to purge the air from the hoses. Some noise squeal may be noticed due to the air.
  1. Carefully remove the rubber fill plug from the back and the reservoir and check the fluid level. The level should be at the bottom of the filler hole. If necessary, add Synthetic Mercon® Multi-Purpose Automatic transmission fluid E6AZ-19582-B (ESR-M2C163-A2) or equivalent.
  1. Replace the fill plug with a new fill plug.
  1. To install, reverse Removal procedure.

Jan 21, 2011 | Ford Mustang Cars & Trucks

1 Answer

The hydraulic pump does not shut off and the lift arms will not go down on my d19 allis chalmers tractor.


Sounds like you have a hydraulic flow valve problem. Check the lift arms when the pump is running to see if you have any hydraulic fluid leaking there.

Nov 18, 2010 | Dmm Allis Chalmers Tractor D19,d21,210,220...

1 Answer

Ford 4000 hydraulic problems


First, make sure there is plenty of hydraulic oil in the reservoir
2nd, no leaks that are dumping the pressure
3rd, no blockage in tubes, located inside pump housing.
4th, make sure operating handle is engaging
try these and if nothing works let me know.

Jan 23, 2010 | RTO Ford Tractor 2000 3000 4000 5000 Water...

1 Answer

Hydraulic lift will pump up about 1/3 of intended height. At that point pedal feels soft and lift won't rise more.


What are you talking about, the bike or the bike lift?

If your hydraulic bike lift is doing what you say, it is low on hydraulic fluid, check the reservoir. HINT: The reservoir is the housing where the shiny bar extends out from; there will be a fitting on it that can be removed to check hydro levels. HINT: Before you remove that fitting, MAKE SURE THE LIFT IS ALL THE WAY DOWN; if you try this with it up, you will spray hydro fluid everywhere.

Jan 21, 2010 | 2004 Harley Davidson FLHTC - FLHTCI...

1 Answer

Hydrolic lift. Fluid is leaking from breather


Hydraulic lift seal needs to be replaced so that the fluid
will not be pushed out. Okey, God bless you.

Oct 12, 2009 | Plumbing

Not finding what you are looking for?
Garden Logo

Related Topics:

643 people viewed this question

Ask a Question

Usually answered in minutes!

Top Garden Experts

Dennis Key
Dennis Key

Level 3 Expert

2478 Answers

roeb

Level 3 Expert

630 Answers

john h

Level 3 Expert

12744 Answers

Are you a Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...