Question about Lexmark X2350 All-In-One InkJet Printer

1 Answer

Need set up cords (pictures of)

Was given printer unit without any cords, users manual or disk for drivers. Can you send me a picture of the cords needed? etc,etc. Thank you

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 233 Answers
Re: Need set up cords (pictures of)

You can get the driver here

I would have to see the back of the printer for the cord types
but if it's an old printer you will probably need a parallel printer cable and the power. you can always take it to a place like radio shack and they will be able to tell you what to get. or you can post a photo

thanks for rating

Posted on Jan 13, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

3 Answers

It only prints half of the picture. How do you remedy this?


The printer driver is corrupted and needs to repair it by adding new printer with the same printer name and set it as default. Then delete the old printer icon. If prints the test page, then it solves your problem.

If still not working, uninstall and reinstall the printer driver which will refresh the printer driver itself. then set up the printer again.


Feb 17, 2011 | Kodak EasyShare Printer Dock Series 3


How to test, and setup the Fax machine on HP multifunctional printers.


Please follow the instructions below to install and test the fax on an HP multifunctional unit.

1 - before connecting the printer install the software in the CD provided with the printer on the computer. The fax unit will also work in stand alone mode, but without installing the software you will not be able to control the unit from the connected computer.

2 - Have ready a phone cable. Ensure that the phone cable that you want to use has only two connectors:


3 - Connect one end of the telephone cord to the telephone jack andthen connect the other end of the cord to the socket labeled 1-Line on the back of the HP fax printer.


4 - The multifunction HP is now ready to send and receive Fax.

To send a basic fax:

1. Load your originals.
2. Enter the fax number by using the dial button on keypad.
3. Press START FAX Black.If the device detects an original loaded inthe automatic document feeder, it will send the document to the numberyou entered

If the Fax is not sending, then check that the original is loaded properly, then run the fax test following procedure below:

  1. press Setup
  2. select Tools
  3. select Run fax test
  4. press OK

  1. Load the original into the input tray.
  2. Press the Setup button (the one with a wrench) on the unit control panel.
  3. Press right arrow, select Tools, then press OK.
  4. On the Tools menu, press the right arrow to select Run Fax Test, and then press OK. The fax diagnostic test prints.
  5. Review the report.
If the test does not return ALL PASS , then setup the fax manually.

Change the HP fax settings
  1. Disconnect the telephone cord from the single-line telephone and then plug it into the port marked 1-Line at the back of the HP product.
  2. Press the Setup button (the one with a wrench) on the product control panel.
  3. Press the right arrow to select Basic Fax Setup or Advanced Fax Setup, then press the right arrow again to change settings to the settings listed in the table below.

After verifying Fax settings, try again sending a fax.

If still no luck, try calling the HP number listed on your user manual. In that case there may be a fault.

Also ensure that you do not have a VOIP phone rather than a landline phone, in that case setup will be completely different.

You can find driver software and manuals using the link below:



on Feb 26, 2010 | Printers & Copiers

1 Answer

Hello, I just purchased the 7200 Series printer. I have a photo event and would like to print pictures using thid printer without a computer. I will be using a SD card. Can I set up my printer without a...

In a word yes, please go to page 16 in this link and read the info given. Its pretty detailed and gives you all the answers you need.

Dec 04, 2010 | Printers & Copiers

1 Answer

My Kodak ESP5 won't scan...

Try to install the latest version of Printer software from on your computer. then open the kodak home center software and click on scan pictures. Adjust the settings and you are ready to go. download the user manual from may be problem with scanner drivers. new software will fix up your issue. Enjoy.

Apr 16, 2009 | Kodak ESP 5 Printer

1 Answer

Lexmark x2470 printer

You can get the User's Guide and other related documents here .
If you did not get the printer software cd, you will also need to download and install the drivers/software from here. Just chose your windows version.


Apr 02, 2008 | Lexmark X2470 All-In-One InkJet Printer

4 Answers

Instructions manual for Lexmark Polaroid p310 photo printer

This link will take you to a manual for the Lexmark 310/315 series. It doesn't show the P310 Photo Printer exactly but the information can be helpful. On Page 15 is tells you how to get the printer to print exactly the picture you want. You need to refer to the instructions that came with your camera for PictBridge connection and usage. It helped me.

Oct 21, 2007 | Lexmark Polaroid P310 Photo Printer

Not finding what you are looking for?
Lexmark X2350 All-In-One InkJet Printer Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexmark Printers & Copiers Experts

Roopesh S
Roopesh S

Level 2 Expert

228 Answers

Sanath Kumar V

Level 3 Expert

684 Answers


Level 3 Expert

18258 Answers

Are you a Lexmark Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides