Question about Washing Machines

1 Answer

Final spin failure

I have a Kenmore model 41743142200 front load that won't spin. It stopped working and I found that the belt had fallen off, after replacing it, now I find that washer does everything but spin. During the spin cycle it turns several times in one direction then stops and repeats in the other direction, I hear a solenoid engage then nothing, the cycle never ends.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,294 Answers
Re: final spin failure

Check your exit hose spigot, it may be clogged. This is if your filter is all clean. There should be air for passage in the standpipe behind. Your hose should not fit airtight into the standpipe and neither too deep into it. Snaking out your standpipe would be good too.

Rate me pl.....if helped.

Posted on Jan 07, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Wont final spin

sorry have not come across that model its not within my expertise

Nov 14, 2011 | Washing Machines

1 Answer

Washer will not spin. it will fill then immediatly empty,3 time no spin or wash. belt is on, motor spins freely, the timer does move with cycle but fast kenmore 41743142200

this sounds like a timer problem, but need the make and model number to be sure, this model number will be on a on the rear panel of washer, or with the original owners manual.

Aug 17, 2010 | Washing Machines

1 Answer

Final spin /rinse cycle won"t stop

It's usually a control board problem. sorry for the bad news :(

Jul 07, 2009 | Maytag EPIC MFW9700S Front Load Washer

1 Answer

Loud noise kenmore washer

  • Hi,
  • try these out:
  1. Balance the load
  2. Level the machine
  3. Inspect the water pump for a blockage
  4. Inspect the coupling
  5. Inspect the transmission
  6. Adjust the drive belt tension
  7. Check the motor bearings
  8. Check the drum brakes
please rate my suggestion...

May 22, 2009 | Kenmore Washing Machines

1 Answer

Replacing shocks on front load washer

through the lower door panel in front of machine. Why???? is machine walking , bouncing or other wise?? This machine spins at HIGH Rpm's so most usual problem is one leg maybe unlevel or possible wood floor maybe "giving " as machine spins and allowing the machine to walk...but then again if machine is "old" shocks could be worn out

May 21, 2009 | Kenmore Elite 45986 Front Load Washer

1 Answer

F/L Washing machine doesn't spin

Normal 0 First drop the lower front panel and remove the pump so you can check the hose leading to the drainpump for debris, coins, etc.

Lower front panel has two? screws holding it in place.

Be prepared for water on floor... use shop vac or have several towels ready for water. Recommend putting at least one towel undermachine before removing pump.

Clamps that hold hose to pump can be a challenger to removeand replace. Consider replacing stockclamps with screw clamps.

This is a great fix.... did it last night.. Found coins, screws, etc. in pump. Once I cleaned out the hose area leading to the pump the spin cycleworked fine.

Apr 22, 2009 | Washing Machines

1 Answer

Kenmore model 41743142200

Un plug washer remove belt by lossing the tensioner , bring to appliances center and assemble again /

Jan 07, 2008 | Kenmore 45081 Front Load Washer / Dryer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

285 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides