Question about Maytag Neptune MAH5500B Front Load Washer

1 Answer

Maytag neptune front loader won't start

When i try to start mt washer it will run for about two minutes and stop or it will not start at all. I checked the voltage and it looks good. i was hoping you might have a solution. you can call me at 1-916-803-3739 or send me a email. thank you for your time.

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 196 Answers

Three items can cause this type of failure
1. Door switch
2. Main control board.
3. Keypad console.

Posted on Jan 14, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

3 Answers

2001 pt cruiser stopped running, running fine down the highway then stopped running and wont start

check that the cam shaft is turning ( broken timing belt)
run the fault codes

Feb 15, 2015 | 2001 Chrysler PT Cruiser

1 Answer

What can i do to start mt 96 chevy 4.3l 1500 truck, after ive changed fuel pump, plugs, plug wires, and checked voltage?

When you say you checked voltage...checked voltage to what? did you check to see if you had voltage going to the fuel pump? do you have spark coming from distributor to wire/ plugs, is the rotor ok? need to check weather your missing fuel, or spark so we know what direction to be looking at. you can try spraying ether/starting fluid in throttle body see if it will start up momentarily, that will atleast tell you weather its a fuel related problem or not.

May 05, 2014 | 2000 Chevrolet Silverado

1 Answer

Washer started and then stops mid cycle

Try unplugging it for a minute and plug back in, that should reset it.

Jan 09, 2018 | Maytag Neptune Washer

1 Answer

No spark on 03 dodge neon

There is voltage on all three wires because there is no ground, check with engine cranking. The two wires that go to computer are grounds for coils. You could probably use a noid lite to check for pulse, engine cranking. That should be safe, between primary voltage and one of the grounds. There several ways to visually check for a pulse. If your digital multimeter has a min/max setting, that should work. You could use an l.e.d. but you would have to use resistor.
You changed computer, was it new?

ignition coil-5iatbqqw4bcw3fkj1yoi3lr2-1-0.jpg

May 15, 2017 | 2003 Dodge Neon

1 Answer

I was driving down the street and the signal lights both stop functioning .. Parked car and was gone approximately 15 minutes. Started car and my signal lights are functioning again. Make a 2 minute stop...

Check your battery terminal's, check woltage when engine is off on your battery, check voltage when running. Could be alternator, battery ior something wrong with charging system.

Feb 12, 2010 | 1995 Ford Escort

1 Answer

AFter start of cycle F11 displays and washer stops

The Motor Control Unit has internal failure; repeating under or over voltage, or over current conditions. If failure occurs during high-speed spin the door unlocks after 3 minutes. Possible Causes/Procedure 1. Unplug washer or disconnect power. 2. Check wire harness connections between the drive motor and the Motor Control Unit (MCU), and b etween the MCU and the Central Control Unit (CCU). Check the motor and do a continuity test. 3. Plug in washer or reconnect power. 4. Check the MCU by looking for operations of the drive motor. 5. Check the drive motor for powered rotations. 6. Replace MCU board.

Jun 18, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Whirlpool LSQ9500LQ0 stops runs only for about 2 minutes

Try this first..Same thing happened to me yesterday..

I pulled the washer away from the water source..unscrewed the water lines from the water intake (not the washer)..there is a screen in the both hot and cold screens were filled with debris..after cleaning the screens the washer works just fine..try this easy fix before you start looking into things like the motor or a switch somewhere...

Dec 19, 2008 | Washing Machines

1 Answer

Washer starts, runs a few seconds and stops,does it over and over

Sound like the internal overload on the motor may be going out .Thsi is usuaklly due to bad or worn bearings. If you know anything abotu electricity,take a voltage reading at the motor whe it is in the run cycle(when it stops) If you stil have have the 110Volts to the motor then the motor is bad and need to be replaced.If you do not then you wil have to look elsewhere for the problem.

Dec 14, 2008 | Amana NAV5800A Top Load Washer

2 Answers

Maytag SAV 205 DAWW

Look for a self resetting overload on the motor. many motors have an overload that pops a little red button out and waits for a push to reset. Other overloads will reset automatically because they are hard to access for pushing a button. If there is an overload resulting in a shutdown you will have to determine the cause. I have found motors in washers completely ingulfed in dust and lint (from the adjacent dryer) and not being allowed to dissipate heat. Sometimes a thorough cleaning is all that it needs to run cool and efficiently.

Jan 18, 2008 | Maytag Legacy Top Load Washer

Not finding what you are looking for?
Maytag Neptune MAH5500B Front Load Washer Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

588 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

John Tripp
John Tripp

Level 3 Expert

4655 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides