Well... It depends on how you have your VCR connected. If its Coxial [a fat black cable at the back which has only one connection] then tune it in the preset 0 or something. It it has 2 or 3 different couloured cables, then press TV/AV or TV/Video or something similar on the remote or TV face.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Hi,If I understood correctly you broke antenna out socket of Cable box..ok no problem,your TV and cable box should have other jacs/socket for this connection as well.. Take the A/V output of your cable box into TV possibly with RCA cables..than you can select the channel thru Cable box on TV ..(AV mode needs to be selected on TV )
in order to listen and watch your magnavox
DVD 's "2xRCA audio" and "1x RCA Video" cables "OUT" should go to
Tv or Cable box "IN" connections separately ..("IN" goes to "OUT" of other
..pls remember,Always reverse connected ) (audio will come thru
Receiver and TV.)
Since you successfully connected your Receiver to play video on TV (one way only ) ,here is the second reverse action if you wish to listen or RECORD a program on your TV on magnavox **
you need to connect "Audio Output " as can either be : RCA jacks or
"Optic cable output" or "SCART "connector " of your TV or Cable box .( every TV -cable box has
different type of Audio out jacks ) ** to "iRCA nput or "Optic Cable input" of your magnavox (whichever you want ,based on the necessary cables on your hand ) There you go..Tv/Cable box video and sound are both on the magnavox for recording..
Hope this helps!..if more help requires pls let me know. Take care and please Remember to rate/vote and give me 4 Thumbs Up for me to continue for Helping out the Community :)
Easiest way to connect is with a scart connector from VCR to TV, then just select AV1 from TV (this will depend on what type if TV you have). If you dont have scart, put your aerial into the rear input of VCR, take supplied flylead & connect that from rear output of VCR & connect other end into TVs aerial socket. Insert a pre-recorded tape, press play on VCR & then on TV select channel 0 & tune your TV until the play back picture appears, then store this on TV tuning settings.
1.- Turn off your TV 2.- On the remote control, set the VCR/TV slide switch to TV position. 3.- While holding in SP/EP button, press the code button listed below that corresponds to the brand of your TV 4.- Press TV POWER on the remote control. Once your TV has turned on, your remote is set up to operate your brand
Brand of TV Brand Code Button Mitsubishi 1,2,3 Fisher 0 G.E. VOLUME UP Goldstar 2,9 Hitachi 8 JVC MUTE Magnavox 4 NEC 2,9 Panasonic CHANNEL UP, CHANNEL DOWN Pioneer 6 Philips 4 Proscan VOLUME UP Quasar CHANNEL DOWN RCA VOLUME UP Sanyo 0 Sharp 3,5 Sony VOLUME DOWN Toshiba 7 Zenith INPUT
I finnaly found my VCR Manual, and I'm glad to share this info with you, because I was looking for the manual all
over the web and FOUND NOTHING!. Bye!
Remove top cover of the VCR. Then look near the back where the plug-in and power supply is. There should be a little glass fuse. You should keep that fuse and take it to the store and replace it with same exact one. If your VCR can be self-repaired, than this is the only thing you can try.
Most Philips/Magnavox VCR uses "PL" to indicate that the unit is on Parental Lock. Push and hold the power button on the remote control and wait for the unit to power up. This should be within 7 seconds.
Additionally, most (but not all) Philips/Magnavox VCRs are sub-contracted to Funai. Pls try here for Funai downloads of user's manual.
Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.
YOu should have your our from your cam to the input of your vcr and the output of the vcr to the input of the tv... then simply set your vcr to the input channel that your cam is connected to ans it should show up on the tv, if it does not hit the tv/vcr button on the remote ... hit record and our done