Question about Hotpoint VBXR1090D Top Load Washer

1 Answer

Clothes wet after spin cycle

My hotpoint washing machine will go inn spin cycle but clothes are soaking wet afterwards.had this fixed once before and I believe all he did was change a belt

Posted by on

  • Anonymous May 15, 2008

    wont

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 121 Answers

If its not the belt its your brushes in the motor that need replaced

Posted on Mar 03, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hotpoint WF250 clothes coming out soaking wet after spin?


The fast wash cycle is for a reduced capacity load of approximately 3kg , it does not pump or spin long enough for a full capacity load

Jun 15, 2016 | Hotpoint Washing Machines

1 Answer

Soaking wet clothes after spin cycle


Check and choose a longer spin cycle and see if the fault changes. If so the SPIN cycle is too less or there is less action or speed in the cycle, check the motor speed, check the capacitor to the motor, the spindle friction - if so reset the spindle and drive.

Jan 17, 2013 | Washing Machines

2 Answers

Spin not working properly, sounds ok but clothes are too wet once complete and the independent spin cycle leaves clothes soaking!!!


Sounds like a small blockage in the outlet pipes, possibly just in the filter but check all outlet pipes. Just done one the other day and it was a clothes button that had passed out of the machine through the pump to the outlet pipe but had turned sideways inside the outlet pipe.

Jan 25, 2010 | Hotpoint Aquarius WMA56 Front Load Washer

1 Answer

My clothe come out very wet at the end of the wash cycle


If the pump is clogged and can't release all the water it won't go into final high spin. Remove lower cover and locate coin catch and unscrew it. Water will come out, so be ready. If it's full of stuff, this is probably the problem.

Mar 13, 2009 | Kenmore HE2 Plus Front Load Washer

1 Answer

Whirpool Duet Was. WFW9400SZ01--Spin cycle leaves clothes soaked.


the problem is your spin program is normal but the machine could not do its job usually there is broken pin clucth under the spinning tube and sometimes the spin gear.this is due to overlload problem. you should brought the machine to your trusted machine repairer as this cost you around US 100-200 in comparison if you buy new one

Sep 25, 2017 | Whirlpool Washing Machines

1 Answer

CLOTHES NOT SPINNING DRY


you have something stuck in the pump..a sock maybe or some other small article of clothing

Jan 11, 2009 | Hotpoint -Ariston VVSR1030HWO Top Load...

1 Answer

Clothes still wet after fast spin cycle


Belt loose or motor / motor control board possibly defective

Sep 13, 2017 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

With my hotpoint washing machine the clothes are soaking wet at the end of the cycle, don't know if its not spinning properly or what?


hotpoint machines are renowned for needing carbon brushes to be replaced in the motor they usually last between 12 months to 2 years depending on the amount of use the machine has.i would check these first as they are a common cause of hotpoints not spinning, if they are ok then check the pump and sump hoses for blockages (not emptying water out)

Jul 15, 2008 | Washing Machines

1 Answer

Load remains wet after full cycle (including spin @ 1400 rpm)


Hi Paul, Assuming it is pumping out ok, Unplug the machine tip it back at an angle, underneath you will see a black hose that is attached to the bottom of the drum, remove this, take out the ball and discard it and remove anything that may be in the filter, replace the hose and try the machine.

Nov 30, 2007 | Hotpoint WMA64 Front Load Washer

Not finding what you are looking for?
Hotpoint VBXR1090D Top Load Washer Logo

314 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

vince

Level 3 Expert

1216 Answers

Eric Taylor

Level 3 Expert

560 Answers

ptpumpman

Level 3 Expert

408 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...