Question about Panasonic Workio DP-2330 Printer

2 Answers

How do i fix E04-01 error on my panasonic DP-2500 printer

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 25 Answers

Most of the time an E4-01 is one you can blame on gremlins. I might happen for no reason. If so, you'll have to go in to service mode (function + original size + 3), go to F9, scroll down to ram initialize, and find the command LBP fuser reset. Hit that, it will tell you to reset the power. It should come back up and be fine after that.
If it comes back with the same error, you'll have to pull the fuser out and replace either/or the thermistat or thermal fuse. You can check for continuity after removing the thermistat or thermal fuse and see which one is bad.

Posted on Jan 24, 2008

Ad
  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 22 Answers

Hi Labilo,

I never face this problem but could find some thing valuable for you please see below..

The fuser can not reach operating temperature. This is usually do to a power fluctuation or outage. There are possible solutions to your repair.

FIRST ONE is that it just might need to be reset in service mode. There is a built in "electronic fuse" like the check engine light in your car. Simply might just need to be reset.

SECOND ONE is the Fuser lamp or thermal fuse has blown and need to be replaced. You should hope for the first solution as the second is very labor intensive and will cost big money!

. Give a call to the dealer you bought it from and see if they will walk you through the reset over the phone. If they need to come out to "look over" the machine, have them bring the current version of software so they can update your machine. There have been MANY software updates for this machine.

Hope this post was usefull , kindly let me know by providing your valuable rating.

Thanks,
Robosoft.

Posted on Jan 04, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Error e04-01 dp-2500


Service mode F9/ram initialize/fuser reset/reset power

May 17, 2014 | Panasonic Workio DP-3520 Copier

1 Answer

How does this proplem occur? panasonic dp 2500 error e04-01


This error comes in fuser unit. the temperature is to low. Check the heater lamp, thermoswitch, thermistor and HTC board. Sometimes draping electricity voltage can cause of low temperature.

Mar 08, 2011 | Panasonic Workio DP-2000P Copier

1 Answer

Workio dp 2500 everything is working properly no image on the drum the machine does not report any error


hi just cheq tha scaner lamp is glowing if glowing may you have problem in charge unit or charge crona
thanks

May 13, 2010 | Panasonic Workio DP-2000P Copier

1 Answer

Panasonic DP 2500 paper tray error


Make sure that you don't have too much paper in the tray. There is an overfill idicator on the back of the tray. Push the tray in firmly. Then try to print. If not, reset the printer by pushing "reset" button.

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe


I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Nov 21, 2008 | Panasonic Workio DP-2330 Printer

1 Answer

Error E01-22 - Check Printer on my DP-2500


"E1-22" 5th & 6th mirror assy. sensor problemMirrors are out of position, was someone cleaning the mirrors or touched for it for a reason??? if not the sensors are bad

Aug 28, 2008 | Panasonic Workio DP-2500E Copier

4 Answers

What can I do to fix it ?


What is the problem first? Then maybe a solution..

Jul 21, 2008 | Office Equipment & Supplies

1 Answer

Fill


it is a fuser error

Mar 15, 2008 | Panasonic Workio DP-2330 Printer

Not finding what you are looking for?
Panasonic Workio DP-2330 Printer Logo

289 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Office Equipment & Supplies Experts

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

6712 Answers

jasbo
jasbo

Level 3 Expert

2237 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Panasonic Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...