Question about Kenmore 42822 Front Load Washer

1 Answer

Kenmore Elite HE3

My washing machine is dripping water into the drum after the load is finished. It appears to be going through the cycle fine, but water keeps dripping into the drum.

I don't know if this information will help or not but my husband recently moved it forward to get behind the washer. He unplugged it and turned the water off but didn't disconnect any hoses. After this it started leaking water after the load.

Interesting though,.... after we run the "drain & spin" cycle, we don't get any dripping....

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers
Re: Kenmore Elite HE3

I don't know if this will help or not, but my machine has gone through (2) fill valve assemblies so far. In one case, it wouldn't fully shut-off and was also erratic. I replaced it (very easy to do) and that fixed the problem. I think my machine is an HE2, but I'd guess it's probably the same parts... (Parts available through the Sears web site. The last one I bought was around $55 for the assembly.)

Posted on Jan 02, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Lights keep flashing and door locks without finishing cycle

Kenmore HE2 Plus Front Load Washer Keeps unlocking ... > ... > HE2 > Kenmore HE2 Plus Front Load Washer
flashing prewash and add garment lights My HE2 Plus will fill with water, but when ...Kenmore HE3 2plus wont finish cycle Washer wont finish the last1 minute of cycle. ...We ran a load twice and it still did not unlock. du is the code for cannot ... Why does the door keep unlocking and locking in between the drum rotating?

Admiral, Whirlpool, Maytag - Washer Repair - Not ... - YouTube

? 5:51
Sep 6, 2013 - Uploaded by
Troubleshoot your Admiral Top Load Washer that has these following symptoms: Not Completing all Cycles ...

Washing machines - Ariston

Jan 05, 2016 | Washing Machines

1 Answer

I have a Kenmore Elite He3 model 110.44832. I ran

Open the top and inspect the damper mechanisms that control drum motion in various directions. There may be broken pieces, or just something out of position. Hope this helps!

Jul 01, 2010 | Washing Machines

1 Answer

Error code F9 for kenmore elite washing machine He3T

it will not let you unlock the door because the machines full of water?--the machine will not finish its cycle because the vacume switch is still detecting water , The water will not drain because the pump is blocked with something , probably a wire from your underwire bra,all you can do is undo a pipe undernieth and let the water drain away and take the pump to bits ?There may be an inspection cap somewhere on the front at the bottom

May 23, 2009 | Kenmore 3.8 cu. ft. HE3 Front Load Washer

1 Answer

Kenmore HE3 will not HOLD water, drips out into the pedestal

check to see if there are any rips in the door seal,then take the bottom of the washer off you will see 3 screws holding it on. see if the water is coming out of the pump that is right behind the panel that you took off.

Dec 30, 2008 | Kenmore Elite 45986 Front Load Washer

1 Answer

Kenmore front loading HE3 makes knocking sounds during spin cycle

Ours started knocking several months ago and then progressed to a high pitched sound when in the spin cycle. I manually turned the drum and heard and felt a bearing roughness. I lifted the drum assembly and felt a fair amount of play, which I think the initial knocking noise came from. On the sears web site a new rear drum mount cost 293.00. Today we went and bought a LG model wm2455hw at Home depot, on sale until 2/20/08. I couldn't see paying to repair a machine that only lasted four years.

Feb 17, 2008 | Kenmore Elite 45986 Front Load Washer

2 Answers

Kenmore Elite HE3 washer keeps filling with water

The inlet valve will need to be replaced. Its a fairly simple procedure and a pretty inexpensive part.

Nov 15, 2007 | Kenmore Elite 45986 Front Load Washer

1 Answer

Kenmore Elite Fronloader Water Problem

the water inlet solenoid valve has debris stuck inside of it, thereby not allowing complete "off" mode. best to remove it and clean the water path thoroughly. valve is found by tracing the inlet water hose.

Jun 03, 2007 | Kenmore 46462 Front Load Washer

Not finding what you are looking for?
Kenmore 42822 Front Load Washer Logo

212 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Jesus  Colon
Jesus Colon

Level 1 Expert

12 Answers

Fred Sops

Level 2 Expert

271 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides