Question about Washing Machines

1 Answer

Beko washer BEKO MACHINE DOES NOT TURN DRUM MOTOR OK BUT TWO WIRES CONNECTED TO DRUM SENSOR? BROKEN , REPLACED WITH NEW CONNECTORS BUT NO DRUM MOVEMENT HELP PLEASE

Posted by on

  • 1 more comment 
  • Anonymous Mar 14, 2014

    But the drum does not turn. Beko wn5100

  • Anonymous Mar 17, 2014

    new motor does not turn

  • Anonymous Mar 21, 2014

    Beko WME7247W Drum not turning belt and pump fine

×

Ad

1 Answer

Have you tried the brushes on motor

Posted on Jan 02, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Washer will not spin, it makes noise as if bearings have gone, empties ok and washes ok


Hi if your beko washing machine is causing a problem and wont drain or has a spin problem then you have to check the carbon brushes first.

Also check all waste pipes are clear and inspect the pump I have included this video below.

At our website I am doing self diagnostic videos on these beko's as we speak so all tutorials will be in this link below
How to replace Beko Washing Machine Motor Carbon Brushes
you might find this test video helpful but only do it if you have checked the motor

May 03, 2014 | Beko Washing Machines

1 Answer

My fisher and paykel smartdrive wont agitate or spin but it pumps the water out it , when i spin the drum there is a bumping sound. can i get into the drum part to see if anything has gotten inside?


That is fault code 130
130.(10000010) Single Rotor Position Sensor Error
The Motor Control Module has found an error in the pattern received from the Rotor
Position Sensor. Likely causes of this fault are a bad connection on the harness between
the Rotor Position Sensor and the Motor Control Module, or a faulty Rotor Position Sensor.
Primary Source: Wiring.
Action: Check for corrosion on the RAST connector of the Rotor Position
Sensor and the Motor Control Module connector.
Secondary Source: Rotor Position Sensor.
Action: Check the Rotor Position Sensor with an R.P.S. tester. Replace if
faulty.
Tertiary Source: Motor Control Module.
Action: Replace Motor Control Module.
Quaternary Source: Rotor
Action: Ensure the correct rotor for this phase of machine has been fitted

Jul 31, 2012 | Fisher and Paykel Fisher & Paykel Washer

1 Answer

Hw60-1460d error code3


just fixed mine take large white panel off at rear of machine look straight in below the drum two grey coloured wires going to temp sensor touched one of them and found wire was broken stripped wire back and crimped on new connector push on spade type.checked other one was ok. turned on machine hey presto error3 was gone machine ok hope this helps.

Nov 25, 2011 | Washing Machines

1 Answer

Error message F50


Hi,

F50 means that the Rotation Position Sensor doesn't sense any movement from the motor.
This test checks the wiring to the motor and rotor position sensor; and the motor and rotor position sensor themselves. NOTE: Drain water from tub.
1. Unplug washer or disconnect power.
2. Check to see if basket will turn freely.If basket turns freely, go to step 3. If basket does not turn freely, determine what is causing the mechanical friction or lock up.
3. Remove the console to access the machine/motor control assembly.
4. Visually check that the P5 and P10 connectors are inserted all the way into the machine/motor control. If visual checks pass, go to step 5. If visual checks fail, reconnect P5 and P10.
5. With an ohmmeter, check for 16 ohms resistance at the P5 connector between pins P5-1 and P5-2, and also between pins P5-1 and P5-3.Also measure the resistance at the P10 connector between pins P10-1and P10-7 and verify that the resistance is within the range. If the P5 connector resistance is much higher than 16 ohms, or the P10 connector resistance is out of range.
6. Tilt machine forward to access the bottom of the machine and the drive motor area. Remove the motor bolt, then the motor cover to access the motor connections.
7. Visually check the mounting bracket and electrical connections to the motor and rotor position sensor board. If visual check fails,reconnect the electrical connections, reassemble stator and motor cover.
8. With an ohmmeter, check for continuity between all pins on the P10 machine/motor control connector and the motor rotor position sensor (RPS) connector.If there is no continuity,replace the lower machine harness.
9. With an ohmmeter, check for continuity between all pins on the P5 machine/motor control connector and the drive motor connector.If there is continuity, replace the drive motor.If there is no continuity, replace the lower machine harness.
10. The drive motor and lower harness are good. Replace the motor RPS board and perform the Diagnostics test.
11. If the Diagnostics motor failed, then the machine/motor control has failed: Unplug the washer or disconnect power.Replace the machine/motor control assembly.

Thank you !!

Jun 17, 2010 | Whirlpool Cabrio WTW6600SBT Top Load...

2 Answers

Drum wont rotate


Code LE is a locked motor Error and it is caused by:

• The connector (3-pin, male, white) in the MOTOR
HARNESS is not connected to the connector
(3-pin, female, white) of STATOR ASSEMBLY.
• The electric contact between the connectors
(3-pin, male, white) in the MOTOR HARNESS
and 4-pin, female, white connector in the MAIN PWB
ASSEMBLY is bad or unstable.
• The MOTOR HARNESS between the STATOR
ASSEMBLY and MAIN PWB ASSEMBLY is cut (open
circuited).
• The hall sensor is out of order/defective.

If you need a service manual for that you can find on Here.

Lg WM-2277HW

I hope this helps.

Randy
FixYa Support Team

Jun 08, 2010 | LG WM-2277HW Front Load Washer

1 Answer

Maytag front load washer keeps giving an E3 error during wash, rinse and spin cycles. Not all the time. Sometimes restarting the washer works, othe times not. It seems the error occurs when the tub won't...


The machine control ("main computer board") is attempting to drive the motor but not detecting any tach response from it. The E3 fault code appears when the rotor or the drum is locked or the Hall Sensor is faulty. But the intermittent behavior of the problem suggests a loose wiring connection. Check the harness that connects the Hall Sensor and the motor to the machine control and make sure the connections are snug fit and not corroded. Clean the connectors and terminals then reseat the connections several times to clean off dirt and corrosion build up in the connectors and terminals. Replace the wiring harness if necessary or if it is badly corroded.

Indicate the exact model number of the washer if the problem is not addressed above for further advice.

Jun 06, 2010 | Washing Machines

1 Answer

What does an ''LE'' code mean on a LG Model WM2075CW


Hi


Thanks for using FixYa. Make sure the error is not IE, which means water has not reached to the pre-set level within 4 min. since ERROR inlet valve operated or water has not reached to the normal level within 25 min.

The 'LE' error message indicates the control board has detected that the motor is either not turning, or has locked up for some reason. Monitoring the motor is the job of the Hall Effect sensor board which constantly determines the direction and speed of the motor and feeds that information back to the control board. If there is a problem between what the motor should be doing and what the hall effect sensor says the motor is doing, the 'LE' will be displayed and the cycle will be stopped.

Motor lock can be caused by several things from a loose connector, to a bad motor, or even the hall effect sensor failing or dislodging from it's mount. Any one or more of these components could have caused this error, but it is possible to separate the working from the non-working, just by following a process.

To make sure its not a locked motor, try turning the drum with your hand. And, if you feel some resistance while turning the drum or the drum doesn’t move freely then the motor is locked and you’ll need to get it replaced.

The hall sensor is rather easy to replace, and is covered by a seven year part warranty (in US). Take the back cover off. Take the big nut off and remove the motor rotor. Remove the bolts holding the motor windings. Remove the electric plug on the sensor and unclip it from the motor winding. Snap new sensor on and reassemble. Usually takes under a half hour.

Also check for ---



  • Check for the Connector (3 pin, male, white) in the Wire Harness, check if it is connected to the Connector (3 pin, female, white) of MOTOR. Reconnect or repair the connector.
  • The electric contact between the connectors¡a3 pin, male, white in the Wire Harness and 6 pin, female, white in the PWB ASSY(Main) is bad or unstable.Reconnect or repair the contact in the connector.
  • The Wire Harness between the MOTOR and PWB ASSY(Main) is cut(open circuited).Repair the damaged (open-circuited) WIRE HARNESS
  • The hall sensor is out of order/defective.Replace the PWB ASSY(Main).

Please do rate the solution and revert for further assistance.


Thanks

Rylee

Nov 12, 2009 | LG WM-2077C Front Load Washer

1 Answer

Hotpoint CTD00 dryer, drum not turning


Provided you only have 2 wires to cap ,it does not matter which wire you put on terminals, as they are both common.
Assuming you got the right value cap, 8uf I think, and it still does not go, check for live and neutral to motor, if supply o/k then you probably have faulty motor.
If no power there check for bad or broken connection.
Pls rate this solution

Dec 15, 2008 | Dryers

1 Answer

Error 5


Error 5 refers to the temperature sensor.
On my machine the wire to it had broken at the spade connector connecting to the sensor.
You can access it easily by removing the back panel, the sensor is at the bottom of the drum with one white wire coming from it. I replaced the connector with a sleeved 1/4" spade connector bought from Halfords.
The wire is of poor quality so try to support it so vibrations dont cause the cable to fracture again

Jun 11, 2007 | Hoover HVP16 Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

240 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

yadayada
yadayada

Level 3 Expert

78257 Answers

Brad Brown

Level 3 Expert

16973 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...