Question about EnGenius SN 920 Ultra Cordless Phone

2 Answers

Can not get the second handset to register to the base

I purchased a use EnGeniue SN-920 Ultra Cordless with Two handsets. I did a register test seperstely with each handset and they work OK. When I try to register both handset to the base, the first handset connects and registers OK. When I try to register the second handset I get an error that states 'no connections'. The user manuel dose not have a trouble shooting section.

Open for assistance.
Thanks

Posted by on

  • Joe Linney Jan 03, 2008

    I purchased a use EnGeniue SN-920 Ultra Cordless with Two handsets. I did a register test seperstely with each handset and they work OK. When I try to register both handset to the base, the first handset connects and registers OK. When I try to register the second handset I get an error that states 'no connections'. The user manuel dose not have a trouble shooting section.


    ---------------------------------------------

    Both handset will register individually but when I attempt to add the second handset to the base, handset #2 will not connect, even when I repeat the procedures over and over

    Thanks......Waiting for more tips

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,944 Answers

Hi,

After you got the no connection message after trying to register the second handset...did you try to register it again?

Posted on Jan 01, 2008

  • Damen Wong
    Damen Wong Jan 03, 2008

    Did you try reseting the base and the two phone units and then trying again?

×

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 689 Answers

This is the registration procedure

Step 1: press MENU-6 and select 3 “SET BASE”
Step 2: press the REG key on the master base
Step3: press register to finish the registration procedure.
• After the registration complete, handset 11 and handset 21 can
2-WAY intercom with each other

If issue persists reset the unit start registration by using 2nd unit that currently unable to register. if issue continues please inform for further troubleshooting

Good Luck

Posted on Jan 01, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My phone display's No link to base. Reconnect main bas AC adapter. It is plugged in what now?


I had this problem, and I fixed it by re-registering the phone to the base. Here are the directions for how to do that from the manual:


----->

Registering a handset to the
base unit
The supplied handset and base unit are
pre-registered. If for some reason the
handset is not registered to the base
unit, re-register the handset.
1 Handset:
{MENU}
2 {V}/{^}: "Initial setting"
{OK}
3 {V}/{^}: "Registration"
{OK}
4 {V}/{^}: "HS registration"
{OK}
5 Base unit:
- KX-TG4011 series:
Press and hold {LOCATOR} for
about 5 seconds. (No registration
tone)
- KX-TG4021/KX-TG4071 series:
Press and hold {LOCATOR} for

about 5 seconds until the
registration tone sounds.
If all registered handsets start
ringing, press the same button to
stop. Then repeat this step.
The next step must be completed
within 90 seconds.
6 Handset:
Press {OK}, then wait until a long
beep sounds.
Note:
While registering, "Base in
registering mode" is displayed on
all registered handsets.
When you purchase an additional
handset, refer to the additional
handset's installation manual for
registration.
<-----

See http://service.us.panasonic.com/OPERMANPDF/KXTG4011-MUL.PDF (page 22)

Dec 06, 2011 | Panasonic KX-TG1033S Cordless Phone

1 Answer

Handset won't work


I went through this exercise with a Siemens Gigaset 8800. The solution is to DE-register the handset first. Then register it with your base. This function can likely be accessed in the handset menu. The phone you purchased is apparently still registered to the previous user's base.

May 23, 2009 | Siemens Gigaset 4200 Cordless Expansion...

2 Answers

My phone says no link to base but I am right beside it.


Sounds like the antenna on the base station is not receiving, or the cordless handset is not transmitting -OR- the sets have never been registered to the base station (please look up registering to base station, if the set has never been registered)

Did the cordless set work before?

The base station or the handset may just have a hick up, I would un-plug the base station and leave it un-plugged... now get all the cordless set(s), and take out the batteries from the cordless set(s). Wait for about 15 seconds for all the power to drain out of the sets, then re-install the batteries.

Once all the cordless sets are back up and working, plug in the base station and wait for about 1 minute.
This forces the base station to re-establish and link between the base station and the cordless sets.

Good luck

May 11, 2009 | Panasonic KX-TGA101S Cordless Handset

1 Answer

Register handset to base unit on sn-920


press menu 6 on handset then press base station reg key for 2 sec till L1 L2 L3 L4 LIGHTS FLASH


handset should now show registration no between 10 and 99

Sep 30, 2008 | EnGenius Lands Phones

1 Answer

Uniden Cordless handset


we purchased the uninden 3 pack bundle they worked fine when installed now one handset will light up but the screen comes up blank and the handset won't work also if this can be corrected i would like to know how to purchase one extra hand set and charger

Sep 30, 2008 | Uniden DECT 6.0 Cordless Telephone...

2 Answers

Onetel ot150 plus add handset


I don't have a second handset, but I'll quote from the instruction manual - Try this,

Regsiter up to 5 GAP cpmatible handsets to your OT150 base. New handsets must be fully charged.

You can use the same handset at home as well as the office by registering it to 2 bases.

1. At the base: press and hold "FIND HANDSET". You hear 2 beeps and the in use light flashes. Youa re now in registration mode.

2. At the handset: Press "OK". scroll down (with down arrow) to "REGISTRATION" and press "OK".

3. "REGISTER" is diplayed. Press "OK". Any free base numbers will flash. Enter the number of the base you want using the keypad.

4. Enter the PIN Number (default = 0000) and press "OK"

5. The handset searches for the base and when registration is complete goes into standby mode.

To test the handset is registered. Press "FIND HANDSET" on the base and the handset should begin to ring. Press "FIND HANDSET" again to stop the ringing.


As I say this is taken word for word (with a few spelling mistakes no doubt) from the instructions. I Hope that it solves your problem.

If you still have problems or you don't have the PIN number, the helpline number is 0845 226 7794, or e-mail help@telephoneproducts.co.uk

Mar 09, 2008 | Cable_and_wireless CWD4901 Cordless...

1 Answer

Cordless phone EnGenius SN 920


. A new handset arrives with a handset ID number of 00, to register this handset to your system take the following steps:
  1. On the EnGenius base unit press and hold down both the "Volume" & "Intercom" buttons for about five seconds. You will hear a beep from the base unit. You can now release the two buttons.
  2. On the EnGenius handset (00), press the following buttons: "menu", "6", "1".
  3. A new handset ID number (ie: 12, 13, 14…) is automatically assigned by the base and registration is complete.

Feb 29, 2008 | EnGenius SN 920 Ultra Cordless Phone

1 Answer

Verge cordless phone system v581tad


I believe you have the expansion capacity of the phone all used up. The phone cannot register any more handsets until you delete the handset registered that is not in use. First check the handsets and see what handset numbers they carry. It should be #1,#2,#3,and #4 if it does not then you will have to delete the one that is missing or if it is then delete handset #5.To do this you will have to use one of the handsets registered to the base. First Press the MENU/ OK button then scroll down to ADV,SETTING then Press MENU/OK then scroll down to DEREGISTER then Press MENU/OK. Then ENTER HANDSET PIN would show, if you have not changed the pin enter 0000 if you have enter your pin member. From the next options select HANDSET and press MENU/OK from the next set of options select the handset number you want to DEREGISTER and press MENU/OK from the next option select YES then MENU/OK. Then try to reregister the new handset To do this Press the MENU/OK button then go to ADVANCE SETTING press MENU.OK scroll to REGISTER then press MENU/OK Select the base number displayed then press MENU/OK. PLEASE WAIT will appear. Then from the base press and hold the PAGE button until the handset prompts you to ENTER PIN # .Enter 0000 OR your pin number then you will see PLEASE WAIT. A tone will confirm the handset registration.

Apr 03, 2007 | Uniden Cordless Phone

1 Answer

ID Conflict with Base 1 error


hold the volume and intercom buttons together the in use light will come on and then go to menu on handset press 6 then 1 to regester that should work i just talked to a friend with a telecom buisness and he told me what to do with mine good luck

Jan 08, 2007 | EnGenius SN 920 Ultra Cordless Phone

3 Answers

Doesn't anyone have an answer or some help? Please!!!!


Uniden TRU8885-2 Cordless Phone > User Guide E X P A N D I N G Y O U R P H O N E w w w . u n i d e n . c o m Register the Handset to the Base If you purchase an extra handset, you need to register the handset to the base before use. Only one handset can be registered at a time. The handset ID for the supplied handset(s) was assigned at the factory, which has #1 or #2 in the display (#2 for models that have two handsets in packaging). When you register additional handset to the base, the handset ID will be assigned. 1) Before registering the extra handset, the battery pack must be charged for 15-20 hours. 2) Place the extra handset in the main base unit to begin registration. 3) While the handset is registering, Handset Registering will appear in the LCD. When Registration Complete is displayed, the handset has been registered to the base. If Registration Failed appears, please try these steps again. Extra Handset Extra Handset Charger Charger Main Base Extra Handset + Main Base Charge the handset for 15-20 hours. Place the extra handset in the main base to register. 1 2 3 4 ?An extra handset can be registered when the main base is in standby mode. ?Standby Mode - The handset is not in use and talk/flash has not been pressed.

Jun 26, 2006 | Uniden TRU8885-2 Cordless Phone

Not finding what you are looking for?
EnGenius SN 920 Ultra Cordless Phone Logo

967 people viewed this question

Ask a Question

Usually answered in minutes!

Top EnGenius Lands Phones Experts

Eric Sutherland

Level 3 Expert

512 Answers

John L radiodude365

Level 3 Expert

541 Answers

Bill Boyd

Level 3 Expert

52156 Answers

Are you an EnGenius Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...