Question about Mitsubishi VS-60719 60" Rear Projection Television

2 Answers

The rear projection Mitsubishi VS-60719 begin to flucate between color & B/W

A private company was called and asked to diagnosis the problem. Te repairman stated that the problem more than like the VIde Processor. The repairman took the TV back to their shop and claimed to have replaiced the REB Video Processor Assemby at a cost of $557.49 ($265.00-Part and $250.00-labor).

Since this did "Not" solve the problem , I aksed a 2nd television company to repair the telvision. The 2nd repair company stated that the Video Board needed to be replaced.

According to the 2nd repairman stated that the Video Processor was located on the Video Board.

I want to know if the 2nd repairman's statement is correct. I have refused to pay the 1st repair company because I had to hire a 2nd repair company to fix a problem that the 1st repair company was supposed to have fixed when they "claimed" to have replaced the Video Processor. I am also of the opinion that the 1st repair was unnecessary and maynot have even been done! Though I am not able to prove that the 1st repair company did not replace the Video Processor as they claim, I have refused to pay for the repairs.

Is there any way I prove my suspicions?

Posted by on


2 Answers

The first thing that happened is that the television began to fluctuate between color and B/W. Then horizon lines approximately 3 inches apart begin to scroll vertically across the screen in 15 to 45 seconds intervals.

As instructed I pressed the input and menu button for 5 to 8 seconds and then released the buttons. The message read TV - Y7.

Does this help?

Posted on Jan 03, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 1,153 Answers

Yes if you tell me what was originally wrong with set! First thing that needs to be done is self diagnosis test. You can do this by pressing the input/device button and menu at the sametime on your set after you turn on. Hold it for 5 seconds. It will have a 2 digit sequence blink. This will be the error code. Let me know what it is. For more info

Posted on Jan 01, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer


This is a very common failure on these projection sets and a fairly simple DIY fix. All projection sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.

Common Symptoms include....

  • Screen looks 3D
  • Colors don't line up
  • One or more colors can't be adjusted when using the convergence menu.
  • Screen is bowed or warped.
  • TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.
Here are some images of convergence problems.


69189a5.pngSOLUTION #1

For more more examples and find a fix using this link on Fixya

Or goto the site for the parts and instructions on how to fix it yourself.

Nov 27, 2010 | Mitsubishi VS-60719 60" Rear Projection...

1 Answer

VS-60719 60 in. Rear Projection Television: Blue Convergence is off, can't solve by using the ...

When the convergence problems happen.100% ur tv convergence board the 2 STK convergence ICS,and some or all it resistors are dead.These parts must be change,to be solved convergence problerms.Tries Websites like, to buy a convergence kit to repair it ur self.Only if u know how to do soldering,and have soldering equipments and solders.The shop will cost u $300-350 for the parts and labors.

May 18, 2010 | Mitsubishi VS-60719 60" Rear Projection...

1 Answer


you need to have someome come out and converge the colors

Nov 06, 2008 | Mitsubishi VS-60719 60" Rear Projection...

1 Answer

Need anwsers asap! Mitsubishi VS-60719 60 in

Can you psot a picture of what the lines look like and I will try and help you out with it. Please reply to this same post each time. Thanks

Aug 06, 2008 | Mitsubishi VS-60719 60" Rear Projection...

1 Answer

TV has sound but no picture

First do the self diagnosis test to see what area is effected, search threads here or goto

Dec 02, 2007 | Mitsubishi VS-60719 60" Rear Projection...

1 Answer

Mitsubishi VS-60719 60" Turns off

replace the regulator and check for bad connections

Sep 21, 2007 | Mitsubishi VS-60719 60" Rear Projection...

1 Answer

Mitsubishi vs 60719 - Wavy bow in picture

Either a bad solder connection on your convergence module or a bad convergence IC. Repair costs will probably be in the $350-$500 range.

Jan 28, 2007 | Mitsubishi VS-60719 60" Rear Projection...

Not finding what you are looking for?
Mitsubishi VS-60719 60" Rear Projection Television Logo

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1213 Answers

The Knight
The Knight

Level 3 Expert

74999 Answers

Jaime Hernandez

Level 3 Expert

2326 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides