Question about Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

3 Answers

MOLD building on inside of dishwasher

I use all the recommended "Jet Dry" materials I was informed by the company and also have been using the HEAT part of washing my dishes. A black mold has started to build up on the inside....very unhealthy I would think? HELP...Just had the repair man out and found that everything is in working order......thanks

Posted by on

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,314 Answers
Re: MOLD building on inside of dishwasher

Are your dishes comming out dry at the end of the dry cycle and during dry cycle do you see steam comming out of the vent

Posted on Dec 31, 2007

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 2 Answers
Re: MOLD building on inside of dishwasher

I just found black mold and mildew gooey stuff in my dishwasher tonight. I took the racks out to see why my dishes are coming out dirtier than when I put them in. That is when I discovered the black mold and mildew. I use my dishwasher daily, and just a month ago, I used a dishwasher cleaner by Cascade I believe. I am totally mystified how mold can grow when I use it daily, dries thoroughly, and vents are clear. This is new to me. Now I am just trying to figure out how the rollers go back on my top rack so I can get it back in~! I'm going to have my home checked for black mold. My water faucet in the kitchen is a "pull out spray faucet", and I shined a flash light in the faucet when it was pulled out, and it is full of mold too. If you find a solution, please let me know!! Good luck!!

Posted on Nov 03, 2011

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 319 Answers
Re: MOLD building on inside of dishwasher

First, remove the mold!

If you wash infrequently, and you do not allow the DRYING cycle to work, then you may have water left in the Dishwasher basin after running a load. If the water remains in the basin, and the door is closed, then mold will form! Use the DRYING cycle. Or if you don't want to use the DRYING cycle, leave the door open for awhile after each load to allow light in, and moisture out!

If you do use the DRYING cycle, ensure that a small amount of "Steam" is coming from the vent at the top of the Door.

Hope this helps!

Posted on Dec 31, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Black mold in my stainless steel dishwasher

use a part of water and baking soda with molds are frequently associated with poor indoor air quality that arises after fungal growth on water-damaged building materials.....

Dec 09, 2013 | Dishwashers

1 Answer

Black Mold on Miele Dishwasher.

Dear Sir:
You must contact to your company supplier, and explain the problem
Can be the possibility that there are some bad design materials, and get some new replacement with better design material. Is not there the first time that this thing happen.
Get the support online, right now.
God bless you

May 15, 2012 | Dishwashers

1 Answer

White film on dishes and interior

White streaking is caused by too much rinse agent. (jet dry) Most all dishwashers now have adjustable rinse agent dispensers, so you can set them to a lower setting when you have soft water, and a higher setting if you have harder water. The adjustment is generally right where you add the jet dry. Other possiblilities would be a leaking jet dry cap, or a defective jet dry dispenser.

Apr 16, 2010 | Jenn-Air 24 in. JDB1090AWS Stainless Steel...

1 Answer

I have mold in my dishwasher. This happened about 6 mos ago and I used the vinegar and scrub method to get rid of was a pain in the fanny! Now the mold is back...the dishwasher has also not been...

Get rid of the mold - Pour about 2 cups of bleach in the dishwasher with about 1 cup of salt, and a gallon of cold water, use the light wash, not heated. Make sure when you start the cycle it doesn't drain first or you lose the bleach. Also I don't use jet dry in my dishwasher, I use bleach in place of jet dry and I've never had a mold problem. Good Luck and let me know if this helps. Thank You

Mar 23, 2010 | Dishwashers

1 Answer

We own a Bosch SHU5307UC dishwasher. Recently, during the 60 minute cycle, the foam builds up and at the end you can see all of it on the bottom. And the last minute dispaly stays on for a while. It...

the unit is over sudzing cut back on soap and dont clean dishes and then put them in dishwasher.dont use to much of the soap with jet dry. regular soap without jet dry in it then add and fill jet dry compartment

Dec 01, 2009 | Bosch SHU5307UC Built-in Dishwasher

4 Answers

Dishes have a powdery residue

If there is not enough water, the dishes would not get cleaned. This could be caused by a partially closed water shut-off valve (located under the sink), or a faulty dishwasher water valve (located at the bottom of the dishwasher, behind the kick panel, on either side).

Also, There is usually two, sometimes three spray arms in a dishwasher. Make sure there is no debris blocking the holes inside each spray arm.

**Water temperature Note***

To get the best results, the water has to be at 120 degrees Fahrenheit when entering the dishwasher.

NOTE(((excessive calcium build up inside the dishwasher can cause this as well. I recommend cleaning the inside of the unit with a dishwasher cleaner called Dishwasher Magic. its good stuff and it will get rid of that calcium build up)))

Jul 30, 2009 | Jenn-Air JDB1105AWS Stainless Steel...

1 Answer

LG dishwasher model #LDF6810ST doesn't DRY DISHES.

ok ...first the average dishwasher will only heat the water 1 degree per mintue,,,now if your starting out with very cold water the dishes will never get clean check your water temp,,at start up..if you have 90 to a 100 degrees thats ok..that means we have problem in heater circuit...also turn up your jet dry level...keep me posted onthejob,,incase we have to look at heater circuit

Dec 31, 2008 | LG LDF6810ST Stainless Steel Built-in...

1 Answer


get valves on both cold and hot water coming into the dishwasher, I would first turn the cold all the off and the hot midway try it. ps: it might only have a hot coming in. if still problems keep turning that hot down perhaps too much hot water is all i can think of. good luck

Aug 31, 2007 | Kenmore 18 in. 14432 / 14439 Built-in...

Not finding what you are looking for?
Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher Logo

1,363 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Dishwashers Experts


Level 3 Expert

4342 Answers

Carmen Mikulic

Level 2 Expert

409 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Frigidaire Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides