Question about Insignia IS-DVD1001 DVD Recorder/VCR

1 Answer

Insignia IS-DVD100121 When I attempt to dub VHS to DVD, it only records for 1 minutes then completely shuts down. I have tried various VHS tapes and the same thing happens each time. What am I missing?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 1,003 Answers
Re: Insignia IS-DVD100121


Posted on Feb 02, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Need manual for toshiba D-vr 610 recorder

For VHS -> DVD dubbing, make sure that you put in a compatible writable DVD with enough space for the video. For dubbing a DVD to VHS, make sure that you have a VHS tape with the erase protection tab on the tape. Insert the blank media in the correct side and the media that you want to record in the other. Press Setup on the remote, then select the General Settings menu. Then select Recording and finally Dubbing. (Use the up/down arrows to navigate the menus and press Enter to select an option.) Select the type of dubbing that you want to do. Press Setup to exit. Then press the DVD or VCR button (with the item to record) and press play and pause when you reach the point that you want to start the recording. Then press the other device button and press the Dubbing button (on the remote or the unit). Press Stop when done recording the selection.

Note: copy-protected videos can't be dubbed.

Crutchfield and Toshiba both have the manual for the DVR-610 . Crutchfield has the manual here: . See page 49 for a set of screen captures of the steps for duplicating a video.

I hope this helps.

Cindy Wells

Jan 20, 2012 | DVD & Blu-Ray Players

1 Answer

How do you record dvd to vhs and from vhs to dvd

For VHS to DVD, put the tape to dub in the VHS slot and a blank DVD in the DVD tray. Make sure the DVD is compatible with the DVD recorder (see the recommended disc list) and is unfinalized if you are using a R/W disc. Close the tray. Set the unit to VCR mode with the DVD/VCR button. Advance the tape to the place that you want the recording to start. Then press the Dubbing button (either on the remote or the unit itself). Select the recording mode (SP, LP etc), highlight Dubbing then press Enter or Dubbing. Press Stop to interrupt the recording.

For DVD to VHS, put a blank tape in the VCR (make sure the protection tab has not been broken off) and the DVD to duplicate in the DVD tray and close the tray. Put the unit in DVD mode by pressing the DVD/VCR button. Find the point at which you want to start recording the DVD. Again press Dubbing and set up the recording mode and highlight Dubbing and press Enter or Dubbing.

Note that copyprotected content can not be recorded.

The manual for this recorder is on the right side of the page here: . See page 48 for the screen captures of setting the recording mode part of the dubbing procedure.

I hope this helps.

Cindy Wells

Mar 19, 2011 | LG RC897T DVD Recorder/VCR Combo

3 Answers

Just got this Toshiba DVR620KU and need to record from home movie VHS to DVD. Have DVD-R, I have set the time, have it on the program VHS to DVD, I start the VHS, put it on pause. Go DVD, select rec...

Good one!

Sounds like you are doing everything right. Only things I can think of are:

- Make sure the disc is a blank one.
- Try a different disc.
- Make sure the tape you are trying to dub is not encoded with Macrovision copyguarding. If it is a home-made recording then you are OK, but a factory recording on a store bought tape may cause some difficulties.

If you are still having troubles try a complete 15 minute reset by unplugging from the power source.

Good luck!

Apr 22, 2010 | Toshiba DVR620 DVD Recorder/VCR

1 Answer

Instructions on how to burn from my insignia DVD to VHS

my Insignia is a different model (NS-drVCR) but I always use the "DUBBING" button on the remote (which is basically the tech-term for a Recording-Transfer). The screen-dialog then shows VHS Dubbing to DVD with quality options to choose. I'm not as familiar with going the other way (from DVD to VHS) but I know that mine can since I've done it once with a similar method, starting with the DUB-button.

Jan 11, 2010 | Insignia IS-DVD1001 DVD Recorder/VCR

2 Answers

I have a Magnavox ZV427MG9. I follow all directions in manual for dubbing VHS home movies to DVD but when I try to play the DVD back there's nothing on them.What am I doing wrong?

Depending on the procedure you may be pressing the record button instead of the D.Dubbing or Dubbing button. When recording from VHS to DVD you must first, load the blank DVD and VHS home movies, then play the VHS movies, then PAUSE the VHS movie when you want to START recording... then the only the you have to do is pressing the D.Dubbing button or the Dubbing button. If your VHS tapes starts to play after the Dubbing button is pressed you have been successful in Dubbing.

Aug 13, 2009 | Philips Magnavox MWR20V6 DVD Recorder/VCR

1 Answer

VCR DVD Recorder not dubbing

I called the manufacturer and realized I was using the wrong type of recordable DVD disc to dub to. Non copy protected VHS tapes dub just fine as long as I'm using the proper disc.

Jun 03, 2009 | Sony RDR-VX530 DVD Recorder/VCR

1 Answer

How do I record my vhs tapes to Disk

I have done a lot of dubbing on my machine. First make sure the DVD is formatted. When you put in a new disc it should ask you if you want to initialize. Once that is done, switch to VCR mode. push play on the VCR then push the DUB button on the front of the machine. I hope it helps.

Mar 02, 2009 | Insignia IS-DVD1001 DVD Recorder/VCR

3 Answers

Will not record on a DVD R

what I would do is play the vhs tape for a bit then rewind and press the dub botton only and see what happens. if nada then insert a new blank dvd and make sure its formated.

Apr 05, 2008 | Sony RDR-VX530 DVD Recorder/VCR

2 Answers


have u tried the seting on the vcr, you know how u can change the lenght of recording on the vhs

Mar 29, 2008 | Philips Magnavox DVD/VCR Dual Player

1 Answer

No Instruction Manual

1. Insert a blank DVD disc in the DVD deck and
close the disc tray.
2. Insert the VHS video tape you wish to copy into
the VCR deck.
3. Find the place on the VHS tape from which you
want to start dubbing using the PLAY, FF, REW
and PAUSE functions. For best results, pause
playback at the point from which you want to
4. Press the DUBBING button on the Remote
Control or DUB on the front panel.
The Dubbing menu appears.
5. Use the arrow keys to select the desired Record
Mode: EP, LP, SP or XP.
6. Select [Dubbing] then press ENTER or DUBBING
to start copying.
7. To stop dubbing at any other time, press STOP (x).
Dubbing will stop automatically when the VHS tape ends.

Mar 01, 2008 | Insignia IS-DVD1001 DVD Recorder/VCR

Not finding what you are looking for?
Insignia IS-DVD1001 DVD Recorder/VCR Logo

499 people viewed this question

Ask a Question

Usually answered in minutes!

Top Insignia DVD & Blu-Ray Players Experts

Cindy Wells

Level 3 Expert

4723 Answers

The Knight
The Knight

Level 3 Expert

66685 Answers


Level 2 Expert

224 Answers

Are you an Insignia DVD and Blu-Ray Player Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides