Question about YDI Outdoor Wireless Bridge in a Box 802.11b (brib)

1 Answer

Wireless i have 12 km wireless brige. i have facing problem, it was working fine before but know it is not working, what should i do.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 55 Answers
Re: wireless

You should reset it back to it's default. there should be a reset button at the back of it. once you've set it back to it's defaul then you should set it up again. Let's hope this works for you

Posted on Dec 31, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

2 Answers

Dlink external antenna configuration

Hi .In my Experience if you Change the Antenna Must be equal Both are Antenna Like 12 dbi Otherwise you are facing the Slow Issue.
must be same DBI Antenna (on my Experience 2700 AP I Face same issue ) when i change the Antenna both are Equal It s Fine working Thanks

Feb 04, 2014 | Wireless Access Points

1 Answer

Hi, I'm using a Belkin N1 wireless router. I mostly have a stable internet connection, but once in a while the "wireless" icon start blinking orange. What is this? My internet some times get...

if the wireless light is lit up in red it says "someone is trying to connect to your network using wrong password"
Sometimes if any of your devices are not compatible with the security enabled in the router then the light will lit up in red. click here to know more about security types of belkin router
routers has to be turned off atleast 2 hours per day for it to work properly... so better turn off the router when not in use, this will clear the routing table of your router and will make the router to work as a fresh router everyday, so you wont face any speed problems.

May 03, 2011 | Belkin N1 Wireless-N Wireless Router

1 Answer

Why belkin n1 wireless router security light is flashing ?


Step 1 : Connect Router - Computer ( Wired)

Step 2 : Open Router Setup by typing on the address bar of internet explorer

Step 3 : On the left under wireless click wi - fi protected setup

Step 4 : Leave the password blank and click on submit

Step 5 : Disable it and Click on apply changes

Step 6 : On the left under wireless click Security

Step 7 : Enable 64 Bit WEP

Step 8 : Type a 10 digit number on the key 1 ( 2 in each box )

Step 9 : Click apply changes

Step 10 : on the left under wireless click channel and SSID

Step 11 :Change the Wireless channel to 6

Step 12 : Change the SSID to a different name ( no Spaces )

Step 13 : Click apply changes

Step 14 : Now Scan and connect to this network ( Wireless )

Let me know if it works

Aug 17, 2010 | Belkin N1 Wireless-N Wireless Router

1 Answer

I have my face book but i cant get into my farm ville i dont know why please can u help me out

If u r able to connect to internet then just go ahead and reset the internet explorer settings. To do that--
Open internet explorer.
Either in the menu bar or on the top left hand side u have TOOLS, click on tools
Then go to internet options.
Click on the last tab ADVANCED
Then click on the reset button on the right hand bottom side.
Then close the internet explorer and then check your game.
It should work fine.

Jun 10, 2010 | Wireless Access Points

1 Answer

Is the PTP 400 Full 5.4 GHz effected by fog and other weather conditions? Have link that goes down in performance in foggy weather.

How far away is your other antenna?

2.4 GHz signals may be attenuated by up to 0.05 dB/km (0.08 dB/mile) by torrential rain (4 inches/hr). Thick fog produces up to 0.02 dB/km (0.03 dB/mile) attenuation. At 5.8 GHz, torrential rain may produce up to 0.5 dB/km (0.8 dB/mile) attenuation, and thick fog up to 0.07 dB/km (0.11 dB/mile). Even though rain itself does not cause major propagation problems, rain will collect on the leaves of trees and will produce attenuation until it evaporates.

Nov 23, 2009 | Motorola PTP 400 Series Full, 4.9 GHz...

3 Answers

How do you find out what wireless router i have on my computer

The problem tat u r facing is tat after the format the drivers of your wireless card is missing.u need to know the name and the brand of the wireless card u r using,,and install the drivers again,,u might have a cd called resource cd from ur computer manufacturer,,that contains the drivers,,or u can call up tec suppoort of your manufacturer to know the name of the wireless card and how to download the drivers from the net,,best of luckk,a good rating plz

May 15, 2009 | Dynex Enhanced-G Wireless Broadband Router

2 Answers

Cannot connect one d-link dwl-7700ap to another d-link dwl-7700ap

You have to add the MAC address from one unit into the other and Vice versa. Set them up in the repeater mode.
The product manual is on this link, under the Support Resources:
copy and paste the complete link into your browser.
If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe

Nov 27, 2008 | D-Link DWL-7700AP AirPremier Wireless AG...

1 Answer

Wireless-G 2.4 GHz 54Mbps Broadband Router serial # CDFG1G777328

If you have your receipt - most wal-mart stores have a pretty good return policy. Present the device and the receipt to the customer service desk is the usual procedure.

Nov 09, 2007 | Linksys (WI-FI COMBO KIT)

Not finding what you are looking for?
YDI Outdoor Wireless Bridge in a Box 802.11b (brib) Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top YDI Wireless Access Points Experts


Level 3 Expert

18258 Answers


Level 1 Expert

15 Answers

 C. Dante
C. Dante

Level 3 Expert

623 Answers

Are you a YDI Wireless Access Point Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides