Question about Sharp Aquos LC-42D62U 42 in. LCD HDTV

1 Answer

Volume control when my 42 inch sharp aqous lcd tv is on a digital channel, or watching a dvd, there is no difference in volume after 30, from 30 to 60 everything sounds the same

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.


    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 53 Answers
Re: volume control

I am a Sharp servicing technician and I have seen this "problem" with this particular model many times. I have tried replacing the Main Board and the Terminal Board and it does not help. The reason i put "problem" in quotes is because I came to the conclusion that this is model is just not that loud. However, a few months after the initial production run, BAM, these TV's are as loud as any other TV on the market so sharp must have caught onto this.

Posted on Mar 14, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

2 Answers

42 inches LCD TV,Aqous brand. where to buy parts inthe philippines

Sometimes the lizards can cause a lot of board wear-off as they being highly conductable and when shorted within the electrical circuit can make the secretions runs into the board therby contaminating and shorting circuits. If you are able to remove and use petrol to wash off the dirt on the board, look for open tracks that have burned or corroded. If you are able to trace and rewire using thin strands of wires , and assuming that no component damage had taken place, you can try this out.
If not as suggested you need to find the cost of a new board if a final consensus is taken.

Nov 07, 2011 | Sharp Aquos LC-42D62U 42 in. LCD HDTV

1 Answer

Has sharp 42 inch aqous got inbuilt digital tuner

Hi www_andremou
You are right. It has got a digital tuner. After you power on, press the Menu button on the Remote Control, select Setup. Select the Auto Installation. The Inbuilt digital Tuner will search for all the available channels r and tune automatically.
If you wish change the Volume and Screen etc
The Instruction manual gives full details.
Good Luck

Dec 01, 2009 | Sharp Aquos LC-42D62U 42 in. LCD HDTV

1 Answer

I have a Sharp 32 inch 720p tv, power works, no other buttons do

Unplug TV set from the outlet, wait 30 seconds, plug it back in, select right input with your remote if you using cable box or Punch the channel that you want to watch if you have cable service connected directly to the TV.

Nov 05, 2009 | Sharp LC-32SB23U 32 in. LCD TV

1 Answer

Sharp Aquos LC-52D64U LCD-52 wdscrn tht won't scan in digital...

Seeing that you have a superior brand and not getting channels is a bummer. It may have to do with the setting, make sure you're set to cable rather antenna and then do a rescan. Btw, often times channels from an over the antenna is much clearer than from cable because cable tv has to compress the signal. If you're high in the air like the top floor of a building a cheap $10 will pull in great free digital channels. It helps to experiment and read the troubleshooting guide in your manual.

Dec 03, 2008 | Sharp Aqous LC-26D5U Television

4 Answers

Freeview channels (DTV) on a Sharp Aquos TV

On my Aquos it's saying no carrier and database empty what do I do, I have trying to reset TV but free view isn't coming on and it's saying carrier 0.

can anyone help

Nov 22, 2008 | Sharp Aquos LC-37G4U 37 in. HD-Ready LCD...

1 Answer

Sharp aqous 42"LCD..will not recieve digital over the used to !!..any ideas???

First make sure you have a good signal, one you know definitely works. Then make sure you connect to coaxial input on Television. Put television on channel 4. Which is good indicator. If no picture/ just snow. You want to access your T V's Menu. Go to Channel Set Up. You should see SIGNAL TYPE. Make sure this is set to CABLE. Right below is a AUTO PROGRAM selection. Let the Television run all the way through. You should be able to view Television as soon as this is done. Providing you have a good signal and there is only one Coaxial input on TV. If there's more than one for example ANALOG, or DIGITAL. Try each one. Each Televsion is different. This is this basic troubleshooting steps. I've done this at a hundreds of installations and trouble calls. Good Luck

Oct 22, 2008 | Sharp Aquos LC-42D62U 42 in. LCD HDTV

1 Answer

Sharp LCD 42" Aqous

If the tv's are still under a warranty program then get a repair tech to check it out They have access to technical websites and will be able to diagnose each individual blink code as they refer to different possible causes according to each specific model

Jun 20, 2008 | Sharp Aquos LC-42D62U 42 in. LCD HDTV

3 Answers

Sharp Aquos LC-26D4OU HDTV volume adjustment problems

If you use a digital cable box, it could be that the volume on that isn't turned up all the way. I didn't even realize the box had volume controls until 2 years after I got it...makes a HUGE difference now

Jun 14, 2008 | Sharp LC-26D43U Television

1 Answer


Best would be hdmi next would be component, both can carry 1080p signal, but hdmi beats component as it can upscale to 1080p.

Jan 21, 2008 | Sharp Aquos LC-42D62U 42 in. LCD HDTV

2 Answers

Remote volume control for Sharp Aquos 42inch LCD not working

ok please open the remote then clean it with pencil eraser.

Oct 09, 2007 | Sharp Aquos LC-42D62U 42 in. LCD HDTV

Not finding what you are looking for?
Sharp Aquos LC-42D62U 42 in. LCD HDTV Logo

376 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sharp Flat Panel Televisions Experts

The Knight
The Knight

Level 3 Expert

66444 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Dave Naylor
Dave Naylor

Level 3 Expert

834 Answers

Are you a Sharp Flat Panel Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides