Question about Galaxy Radios DX- 88HL Base CB Radio

1 Answer

No sound My galaxy just stopped making noise. it transmits and recieves, but nothing comes out of the speaker. i havent oened it to look or hooked it up to an external speaker either.

Posted by on

  • molsonmuscle Jan 03, 2008

    ok. i have it hooked up to an external speaker, it works fine. but nothing out of the onboard speaker. must be blown.

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 211 Answers

It must be a bad internal speaker, but also check the external speaker jack for broken solder. Good Luck
Ed
NC Electronic
Mills, Wyoming

Posted on Jan 07, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No transmit or recieve


sounds like a repair for a tech to me.

Jan 16, 2014 | Galaxy Radios SSB Echo Base Station CB...

1 Answer

I have a galaxy 55 v that will transmit and receive but has no swing


I would turn do the watts to about 3.5 and that radio should swing.Sounds to me like its trying to but the wattage is stopping it.Experiment with it and find where you want to set it.

Jan 26, 2013 | Radio Communications

2 Answers

Galaxy 99v off Frequency


it is either a bad soilder on your crystal or your crystal is going bad

Dec 15, 2009 | Galaxy Radios DX-99V 40-Channels Base CB...

2 Answers

President HR-2510 will not transmit or recieve


Hi Darrel,

Since you didn't say if you have ever used this radio successfully before, I have to assume it is "new to you" and that you have never seen it work or used one like it before. Start with a few basic settings below:

Turn Squelch to minimum.
Set RF Gain (if present) to maximum
Set Mode to AM or FM
Set volume to 1/3 up
Connect to 50 ohm dummy load.

Turn power on. Hopefully you hear static. If not, try SSB or FM. Still nothing? Try connecting to an external speaker.

Chnage back to AM or FM mode. Key mic check & for transmit indicator. If none, change mic or manually short the PTT contacts in the mic or at the radio to see if it can be made to xmit.

If no xmit - insert SWR meter between xmitter and dummy load. Try to xmit on AM or FM again while watching SWR forward power, if none indicated, xmitter is probably defective.

Replacing parts in a xmitter is not recommended. You'll need an FCC license and a fair amount of expensive test equipment to test repairs, set power levels and deviation and perform an alignment to be sure you aren't causing interference on other frequencies and bands.

You'd be better off bringing it to a radio repair shop for repairs and an alignment.

Sep 29, 2009 | Uniden Radio Communications

1 Answer

Denon AVR-1706 Left Front and Rear speakers stopped working. Any suggestions?


go into the settings menu and do a sound test using the recievers pink noise tester to test each speaker connected, if while doing this test you still get no sound from those two speakers check connections, make sure speakers are not blown.
if speakers and connections are good then the reciever needs repair

Jul 18, 2009 | Denon AVR-1706 Receiver

1 Answer

Rushing sound (noise) galaxy 88 HL


RUSHING SOUND ?
1. Get the noise then disconnect the coax and see if noise goes away on receive, if noise goes away then address the ground on your antenna,
if noise still there then address the ground wire from power source

Mar 30, 2009 | Galaxy Radios DX- 88HL Base CB Radio

2 Answers

Onkyo digital reciever has poping noise when in dolby sound


I have the same reciever, and had the same problem.  Contact Onkyo, this is a known issue where defective DSP chips were used and manifest problems with a popping / clicking sound when using surround settings.  These receivers also have a Dolby Digital input issue that can cause audio dropouts when watching cable or SAT broadcasts that encode DD using a 'newer' broadcast encoding methods.  Onkyo is covering the cost of that repair for me now, even though the receiver is 5 years old now....

Jan 02, 2009 | Onkyo TX-DS797 Receiver

2 Answers

ONKYO HT-SR700


Is it only the right speaker that is the problem?

Jan 13, 2008 | Audio Players & Recorders

1 Answer

Cant get rear speakers to Work AVR 745 7.2 Surround!!!


Another way to solve this rear speakers problems is to go to the equalizer and have the system recognizes the sound coming out of all speakers. The AVR 745 comes with a microphone on the stick, using that to run the manual equalizer. It is the manual equalizer will set the rear speakers.

Dec 29, 2007 | Harman Multimedia AVR 745 Receiver

Not finding what you are looking for?
Galaxy Radios DX- 88HL Base CB Radio Logo

Related Topics:

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Galaxy Radios Radio Communications Experts

Brad Brown

Level 3 Expert

17473 Answers

Steve
Steve

Level 3 Expert

696 Answers

Marvin
Marvin

Level 3 Expert

82322 Answers

Are you a Galaxy Radios Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...