Question about Frigidaire Affinity ATF7000EG

3 Answers

Washer stuck on Pause mode

My washer is stuck on the pause mode. I can't reset the computer. I have unpluged it. I have hit cance, pause etc. It is a model where all the led lights blinks 3 times after I try to cancel or restart it. It is affinity ATF7000ESO

Posted by on

  • 4 more comments 
  • Valari1 Dec 30, 2007

    i'll try i tand let you know? I will need to wait for my husband to get home after jan 1 as I don't know where the pressure sensor is.

    Thanks

  • Valari1 Jan 01, 2008

    I have opened the top panel but I cannot recognize the pressure any other this to let me know what I'm looking at



    Thanks

  • Valari1 Jan 01, 2008

    Thans soooooo much. it worked . i just unpluged both things that could have been what you were describing. and it reset

  • Anonymous May 06, 2008

    OMG..... I looked all over to find a solution to the same problem you had. Who needs technicians anymore? Thanks for the answer to my problem! IT WORKED!

  • Anonymous May 19, 2008

    WASHER STUCK ON PAU 50. 3 BEEPS WHEN START BUTTON IS

    PRESSED ERR MESSAGE AND MACHINE WILL NOT START

  • Anonymous Mar 25, 2014

    front load washing machine is in pause mode

×

Ad

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,314 Answers

Remove the washer from the electrical supply.
2. Remove the top panel and disconnect the wire plug to the pressure sensor.
3. Reconnect the washer to the electrical supply.
4. Press start and wait 10 seconds (washer will drop out of the continuous loop).
5. Remove the washer from the electrical supply.
6. Reconnect wire plug to pressure sensor and reinstall the top panel.
7. Reconnect the washer to the electrical supply and verify proper functionality.
8. If same symptoms occur, install a new console control.

Posted on Dec 30, 2007

  • robert samples Dec 30, 2007

    The pressure sensor is under the main top panel it well have a clear see thur hose on it. You can do this my wife is as good as i am she fixes alot of them. The sensor will either be gold or white plastic most always. Look for the screws on the back of the top panel, then remove them. Push the panel back lift it up and then follow directions. Go get'em girl you can do this reply if you need me thanks

  • robert samples Jan 01, 2008

    ata girl knew you could do it i was just getting ready to send you a message with a picture from the svc manuel way to go yaaaaaaa

×

Ad

Thank You very much . I unpluged the sensor and did as you said and than I was able to get into the codes. Again thanks

Remove the washer from the electrical supply.
2. Remove the top panel and disconnect the wire plug to the pressure sensor.
3. Reconnect the washer to the electrical supply.
4. Press start and wait 10 seconds (washer will drop out of the continuous loop).
5. Remove the washer from the electrical supply.
6. Reconnect wire plug to pressure sensor and reinstall the top panel.
7. Reconnect the washer to the electrical supply and verify proper functionality.
8. If same symptoms occur, install a new console control.

Posted on Nov 02, 2008

Ad

Thank you so very much this was the solution to my problem. You saved us at least $200.00 and wailing and nashing of teeth

Posted on May 11, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Washers start button will only flash as in pause in stead start washing ? I unplugged wash to reset computer and still flashing in pause mode ? What's the next step in troubleshooting thanks nicole k in...


You need to get the diagnostic info. It should be located just inside the kickplate. Unplug the washer, and then remove the kickplate. Inside will be a packet of info that will help you diagnose your washing machine.

Nov 21, 2010 | GE WSXH208A Front Load Washer

1 Answer

My neptune washer is stuck in pause mode I can't set it any any wash mode to wash a load the start/pause light just keeps blinking. Is there any way to reset it or boot it to get it started again thanks...


Karen,

Power it down by pulling the 120VAC power cord to the washer then plug back in and see if it will progress with the wash cycle. Which machine do you own the FAV6800A LED console display or the FAB9800A LCD console.

If still no good I will have you try to get into Service Mode but let’s see if a power cycle will clear the issue…….Rich


You will need the Service Manual for reference. Sears Parts Direct for reference.




May 21, 2010 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

The washer is stuck in pause mode. How do I get


Control Lock To avoid having someone accidentally start or stop the washer, press Options and Select at the same time and hold for 10 seconds until “LOC” is displayed alternately with the estimated cycle time. To unlock the controls, press Options and Select at the same time and hold 10 seconds until ”LOC” is no longer displayed.

Sep 18, 2009 | Frigidaire Affinity ATF7000E Front Load...

1 Answer

Canceled the clean washer cycle, got "INT", won't work now


Unplug machine, wait 2 minutes and re-plug. This should reset computer and unlock door.

Mar 10, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Pause mode stuck


Is the door firmly closed? Open the door and close it firmly. If the pause button is really stuck, you will need to repair/replace the board.

Oct 17, 2007 | Whirlpool Duet GHW9150P Front Load Washer

3 Answers

Paused. now stuck. cannot open, turn off, etc.


Unpluggin the machine is pretty much the only way to reset it.Leave it unplugged for a couple hours if that doesnt work its most like a control board issue

Mar 15, 2007 | Whirlpool Duet GHW9150P Front Load Washer

8 Answers

Frigidaire Front Loading Washer, ATF6000ES stuck on pause mode - HELP!


I fixed this myself and it only took about 5 minutes. The problem is the door latch needs to be reset, which requires unplugging it's three electrical connections. This has to be done inside the washer outer seal, but it is easy to get to. First remove the outer ring that holds the seal on. Next remove only the side of the seal closest to the door latch (again only the outer seal needs to be undone). With this done remove the two screws holding the door latch in place (inside). Remove the latch, unplug the three connectors, plug them back in then reassemble everything. When all is back in place hit "cancel" and it should be good to go.

Feb 10, 2007 | Frigidaire ATF6000ES Front Load Washer

Not finding what you are looking for?
Frigidaire Affinity ATF7000EG Logo

1,257 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1474 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Jason Harris
Jason Harris

Level 2 Expert

271 Answers

Are you a Frigidaire Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...